valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
OWNER’S MANUAL & OPERATING INSTRUCTIONS IMPORTANT SAFETY WARNINGS READ AND FOLLOW ALL SAFETY WARNINGS AND INSTRUCTIONS IN THE OWNER’S MANUAL BEFORE OPERATING SPOTLIGHT. WARNING • • • • • • • • • Never place spotlight lens (face) down when light is on or if it was recently on. Doing so could burn/ignite surfaces such as seats, carpeting, etc. and cause serious property damage. Always turn spotlight OFF and unplug from source when not in use. To prevent serious damage to eyesight, never look into spotlight when light is on. Do not shine light into the face of someone else. Do not touch lens of spotlight when light is on or if it was recently on. The lens will be hot and could cause serious burns. Keep battery clips or cigarette lighter plug dry and out of water at all times. Do not place spotlight in water. Keep all components dry and out of water at all times. Do not allow children to handle or operate this spotlight. Do not use this product for other than its intended use. Do not operate in close proximity of combustible or flammable materials. Do not attempt to operate spotlight if cord, plug, bulb or any part of the spotlight is damaged or corroded. USE CAUTION AND COMMON SENSE WHEN OPERATING YOUR SPOTLIGHT. FAILURE TO ADHERE TO THE SAFETY WARNINGS AND GUIDELINES IN THIS MANUAL COULD RESULT IN BODILY INJURY OR PROPERTY DAMAGE. SAVE THIS MANUAL FOR FUTURE REFERENCE. Tips to Avoid Damage to Your Q-Beam Spotlight • Never attempt to wipe or clean the inner reflective surface of the reflector. Touching or wiping the surface will damage it permanently. • The lens is made of optical-quality, tempered glass. As with all glass, avoid dropping or sharp impact on spotlight. • Do not allow the hot lens to come in contact with water or materials subject to heat damage. • This spotlight is weather resistant. It is not waterproof. Do not use the spotlight under water or store outdoors for extended periods. • Only use a Brinkmann 12-volt, halogen bulb that is designed for your Q-Beam spotlight. Use of any other bulb may result in poor performance and may damage your spotlight. • After months of use, cigarette lighters can build up corrosion that may prevent your Q-Beam spotlight from making good contact. It may be necessary to clean the inside of your cigarette lighter receptacle with a fine emery cloth. Before cleaning receptacle, remove the fuse to prevent it from shorting out. OPERATING INSTRUCTIONS READ AND FOLLOW ALL SAFETY WARNINGS AND INSTRUCTIONS IN THE OWNER’S MANUAL BEFORE OPERATING SPOTLIGHT. Step 1: To activate spotlight, plug the cigarette lighter adapter into a cigarette lighter receptacle. Step 2: Depress trigger switch in handle to turn spotlight ON. Release trigger switch to turn spotlight OFF. WARNING: Never place spotlight lens face down when light is on or if it was recently on. Doing so could burn/ignite surfaces such as seats, carpeting, etc. and cause serious property damage. Always turn spotlight off and unplug from power source when not in use. Step 3: To lock trigger switch to ON, depress trigger switch and slide locking button on back of handle to LOCK. To unlock and turn spotlight OFF, slide locking button back to UNLOCK. NOTE: The locking button can also be used to lock spotlight in the OFF position to prevent accidental activation. Only use a Brinkmann halogen bulb that is designed for the Q-Beam 700,000 CP spotlight as a replacement. Use of any other bulb may result in poor performance and may damage your spotlight. IMPORTANT: Do not touch the glass part of bulb with fingers as natural oils affect the life and performance of bulb. Handle bulb by metal end only. Step 1: Disconnect spotlight from power source. Step 2: Remove the two screws from top and bottom of front housing (see Figure 1). Step 3: Holding the front housing securely, slowly remove the rear housing, being careful not to pull wire connections inside. Locking ON/OFF Button To Replace Bulb Rear Housing Front Housing FIGURE 1 Connector Connector FIGURE 3 Connector FIGURE 4 FIGURE 2 Step 4: Disconnect bulb wire from connector by holding the connector firmly with fingers then pulling bulb wire straight out as shown in Figure 2. Step 5: Squeeze the wire retainer together and lift up as illustrated in Figure 3. Step 6: Pull bulb straight out from the reflector mounting plate. Step 7: To install new bulb, grasp the bulb from the metal end (DO NOT TOUCH THE GLASS PART) and insert into the reflector mounting plate. Align the slots in the bulb base with those in the reflector mounting plate. Step 8: Replace wire retainer by squeezing ends together while pressing down. Release ends so that they catch on the reflector mounting plate. Step 9: Reconnect the bulb wire to the connector as illustrated in Figure 4. Step 10: To reassemble spotlight, align screw holes in the rear and front housings, then insert the rear housing into the front housing of the spotlight. Step 11: Replace the two screws that were removed in Step 2. Do not overtighten ...