• DO NOT OVERCHARGE: – AC recharge up to 14 hours maximum. – DC recharge up to 14 hours maximum. • NEVER ATTEMPTTO USE THE AC CHARGER AND DC CHARGING PORTSIMULTANEOUSLY. • After charging/recharging, disconnect charging adapter or extension cord and wait 5minutes before use. • Do not crush, cut, pull or expose charging adapter cords to extreme heat. • Position charging adapter cords so they do not become entangled or become a safetyhazard. Keep charging adapter cords away from sharp edges. • Use

• Do not immerse spotlight in water. • Do not drop or throw spotlight. It contains glass and a sealed lead acid battery. • Only replace bulb with type indicated in specifications (12 volt, H3 75 watt quartz halogen). • Use only with AC or DC charging adapters that are provided with unit. Plug in the charging adapter at the spotlight first, then plug into the charging source. • Do not overcharge: – AC recharge up to 30 hours maximum. – DC recharge up to 4 hours maximum. • NEVER ATTEMPT TO USE THE

3. Loosen and remove six screws that secure spotlight housing. 4. Lift up and set aside the right side of the housing. 5. Remove wire spring and carefully pull out old bulb from the terminal. 6. Replace with a new H3 type, 12 volt, 100 watt bulb, available from an electrical supplyhouse or from Black & Decker (refer to the Service Information section). 7. Reverse the above procedure to re-assemble the spotlight. Note: When handling a new halogen bulb, do not touch the glass portion of the bulb.

Insert the S p o r t S p o t® spotlight 12 volt DC plug into the accessory socket of your vehicle or a portable 12 volt power source, such as a jump starter. 2 . To turn on the S p o r t S p o t® slide the spring-loaded power switch to the ON position (up). 3 . To turn off the S p o r t S p o t®, release the spring-loaded power switch. It will slide back to the OFF position (down). USING THE HANGING HOOK The Hanging Hook allows you to position the unit for convenient, hands-free operation. CAUTI

• DON’T OVERREACH. Keep proper footing and balance at all times. • DISCONNECT APPLIANCE. The AC Charger and DC Charging Adapter should be maintained in a readily operable condition. To avoid damage to the unit or Adapter, disconnect the unit from any power supply when not in use, before cleaning, during lightning storms, and changing accessories or when it will be unused for long periods of time. To disconnect the unit from the power supply, the AC Charger must be completely disconnected from an

Charge after each use until red LED flashes. Charging/Recharging Using the 120 Volt AC Charger and a Standard Household Extension Cord (not included) Plug a standard North American 120 volt AC extension cord (not included) into the 120 Volt AC Charger on the back of the unit. BATTERY STATUS LED INDICATOR BUILT-IN 120V AC CHARGER Make sure the Spotlight is OFF (the Trigger Lock is in the OFF position and the Trigger is not depressed). 3 SL102B_ManualEN_051007.qxp 5/10/07 9:13 AM Page 4 Charge unt

Sliding the switch forward (toward the Spotlight bulb) sets the Spotlight on High Beam; sliding the switch backward sets the Spotlight on Low Beam. Using the Carry Handle as a Stand For Hands-Free Operation Invert the unit to use the Carry Handle as a stand, and set it upon a flat, stable surface for hands-free operation. Using the Built-In Carry Lanyard The Carry Lanyard may be used to store or carry the Spotlight; and also allows you to position the Spotlight for convenient, hands-free operati

IN MOST CASES, A BLACK & DECKER REPRESENTATIVE CAN RESOLVE THE PROBLEM OVER THE PHONE. IF YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER. Catalog Number SL202B TO REDUCE THE RISK OF INJURY, THE USER MUST READ AND UNDERSTAND THE INSTRUCTION MANUAL SAVE THIS MANUAL FOR FUTURE REFERENCE. Cat. # SL202B Form # 90518422 May ’07 Copyright © 2007 Black & Decker Printed in China SL202B_ManualEN_050107.qxp 5/1/2007 4:15 PM Page 1 GENERAL SAFETY WARNINGS AND INST

• To reduce risk of damage to plug and cord, pull • Use of improper extension cord could result in • Use only the supplied chargers when charging this spotlight or create a hazardous condition. • Use only one charger when charging. • Do not attempt to charge the unit if the charger plug is damaged— • Do not attempt to open the charger. There are no customer serviceable parts inside. Return to manufacturer for repair. • All ON/OFF switches should be in the OFF position when the unit is switches a

Charge unit BEFORE first use using the 120 Volt AC Charger for20-30 hours or until the green Battery Status LED flashes. Charge after each use until green LED flashes. Charging/Recharging Using the 120 Volt AC Charger and a Standard HouseholdExtension Cord (not included) Plug a standard North American 120 volt AC extension cord (not included) into the 120 Volt AC Charger on theback of the unit. BATTERY STATUS LED INDICATOR BUILT-IN 120V AC CHARGER Make sure the Spotlight is OFF (the Trigger Lock