valutazioni - 1, GPA: 3
(
)
)
|
Facilità d'uso
Unit will shut off immediately. (figure 2) • From Hands free use: Slide hands free slide stem to full left position. Unit will shut off immediately (figure 3). CAUTION: 1. Keep out of reach of children. 2. Do not touch flame guard when hot! 3. Butane gas is extremely flammable, please handle with care. 4. Always point away from eyes and body when igniting or operating. 5. Do not store under direct sunlight or anywhere that will exceed 104°F/40°C. 6. Under no circumstances should you attempt to repair a damaged torch. 7. After using, let the tool cool down before storing. Contains flammable gas under pressure. Do not use near sparks or open flame. Do not puncture or incinerate container. To refuel unit. (figure 1) • Make sure the unit is OFF and COOL to touch. • Make sure the protective cap is on nozzle. • Use only Master Ultratane® butane to refuel unit, hold unit firmly with filler valve pointing up. Place nozzle of butane canister down onto refill valve and press butane canister down and up in short duration until fuel tank is filled. Allow 2 -3 minutes for gas to stabilize after filling unit. • Flame is invisible in direct sunlight. Use caution. • Point away from face and body when igniting. • Use in well ventilated areas. • Always have a fire extinguisher/ bucket of water nearby work area. • The tank contents are visible through the clear viewing port on the unit. Designers and Manufacturers of Heat Tools MICROTORCH MT-5 Size dim. 75x32x21mm Unit Weight 45g Internal tank pressure 65 g/mm2 max Continuous burn time 20 min. - one fill Specifications CAP SAFETY LOCKOUT LEVER BODY FUEL VIEW WINDSHIELD IGNITION BUTTON FLAME ADJUSTMENT To ignite unit (figure 2) • Remove safety cap. • Slide lockout lever to off position and hold in position while slowly depressing ignition button. • After a few attempts if no flame appears, fine tune the unit’s gas flow and retry ignition step above. To adjust fuel flow (figure 4) • Adjust the unit fuel flow by turning the black fuel flow adjustment wheel at bottom of unit. A 1/4 inch turn CW/CCW will usually be all that is needed. Note: Extreme caution must be taken not to over adjust fuel flow. If you are unable to make proper adjustment, please call customer service. As the gas is consumed, the gas flow can be adjusted periodi- cally to ensure proper flame height. It is recommended that the user set the flame height to 1/2 inch to 1 inch. If the flame height is set outside these limits the fuel flow / flame may become unstable and cause premature clogging or ignition failure. Hands free mode (figure 3) • To engage hands free mode follow ignition steps above and once the unit is ignited, position slide stem button (found on backside of unit) to full right position. This will allow hands free operation of unit. Fig. 1 Fig. 3 OFF-LOCK Please read and understand all warnings and instructions. 2420-18th Street, Racine, WI 53403 U.S.A. PHONE: 262-633-7791 FAX: 262-633-9745 E-mail: sales@masterappliance.com MORE GAS LESS GAS BOTTOM VIEW GAS FLOW VALVE STEM FUEL ADJUSTMENT Fig. 2 Fig. 4 To extinguish flame / Turn off gas flow • From Normal Use: Release pressure from ignition button. Unit will shut off immediately. (figure 2) • From Hands free use: Slide hands free slide stem to full left position. Unit will shut off immediately (figure 3). CAUTION: 1. Keep out of reach of children. 2. Do not touch flame guard when hot! 3. Butane gas is extremely flammable, please handle with care. 4. Always point away from eyes and body when igniting or operating. 5. Do not store under direct sunlight or anywhere that will exceed 104°F/40°C. 6. Under no circumstances should you attempt to repair a damaged torch. 7. After using, let the tool cool down before storing. Contains flammable gas under pressure. Do not use near sparks or open flame. Do not puncture or incinerate container. To refuel unit. (figure 1) • Make sure the unit is OFF and COOL to touch. • Make sure the protective cap is on nozzle. • Use only Master Ultratane® butane to refuel unit, hold unit firmly with filler valve pointing up. Place nozzle of butane canister down onto refill valve and press butane canister down and up in short duration until fuel tank is filled. Allow 2 -3 minutes for gas to stabilize after filling unit. • Flame is invisible in direct sunlight. Use caution. • Point away from face and body when igniting. • Use in well ventilated areas. • Always have a fire extinguisher/ bucket of water nearby work area. • The tank contents are visible through the clear viewing port on the unit. Designers and Manufacturers of Heat Tools MICROTORCH MT-5 Size dim. 75x32x21mm Unit Weight 45g Internal tank pressure 65 g/mm2 max Continuous burn time 20 min. - one fill Specifications CAP SAFETY LOCKOUT LEVER BODY FUEL VIEW WINDSHIELD IGNITION BUTTON FLAME ADJUSTMENT To ignite unit (figure 2) • Remove safety cap. • Slide lockout lever to off position and hold in position while slowly depressing ignition button. • A...