Log:
valutazioni - 1, GPA: 5 ( )

Istruzioni per l'uso Harbor Freight Tools, Modello 91061

Produttore : Harbor Freight Tools
File Size : 46.77 kb
File Nome : 91061.pdf
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


9. Always allow sufficient time for the Blow Torch to completely cool down before storing. Do not store flammable liquids or materials in the area surrounding the Blow Torch. 10. Maintain labels and nameplates on the Blow Torch. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. SKU 91061 PAGE 4 11. Never use gasoline, kerosene, or other highly volatile fluids as a starter as they can explode. 12. Dress safely. Do not wear loose clothing such as hanging shirt tails and coats. Wear a protective hair covering to keep long hair away from heat and flames. Use ANSI approved safety impact goggles and flame retardant gloves and clothing to avoid burns. 13. Never leave the Blow Torch unattended once it is lit. 14. Keep a fire extinguisher handy. Always keep a commercial fire extinguisher nearby the Blow Torch in case of accidental fire. 15. Do not clean the Blow Torch with cleaners that are combustible or corrosive. 16. Do not paint any part of the Blow Torch. 17. Make sure the Thumb Wheel (7) is turned to its “OFF” position and the propane tank (not included) is removed when the Blow Torch is not in use. 18. Do not use the Blow Torch in the rain. 19. Never smoke while using the Blow Torch. Make sure all surrounding flames are extinguished. 20. Never use a propane tank if it shows signs of: Dents, corrosion, gouges, bulges, fire damage, leakage, excessive rust, or any other form of visual external damage. 21. When work is complete, only set the Blow Torch on a non-flammable surface like concrete, until the tool is completely cool to the touch. 22. WARNING! The brass components of this product contain lead, a chemical known to the State of California to cause birth defects (or other reproductive harm). (California Health & Safety Code 25249.5, et seq.) 23. WARNING! This product, when used with propane fuel, produces chemicals known to the State of California to cause cancer and birth defects (or other repro- UNPACKING When unpacking, check to make sure all the parts shown on the Parts List (page 8) are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. SKU 91061 PAGE 5 PRODUCT FEATURES 1. The Blow Torch is ideal for sweating and thawing pipes, soldering, and burning weeds in a well controlled safe environment. In addition, the Blow Torch easily attaches to standard 16.4 Oz. (465 g) (1.02 Lb.) propane tanks. ASSEMBLY AND OPERATING INSTRUCTIONS NOTE: For additional references to the parts listed in the following pages, refer to the Assembly Diagram (page 8). 1. Make sure the Thumb Wheel (7) is turned completely clockwise to the “OFF” position. (See Figure A.) 2. Screw the 16.4 ounce propane bottle (not included) tightly onto the Cylinder Connector (11). Do not remove the propane bottle until it is completely empty. 3. The Thumb Wheel (7) regulates the propane gas flow. Release the propane gas flow by slightly turning the Hand Wheel counterclockwise. (See Figure A.) 4. Make sure the Burner (1) is pointing in a safe direction and, with the Blow Torch in a vertical position, push the Piezo Button (16) to activate the electric start. It may be necessary to push the Piezo Button several times to activate the flame. (See Figure A.) 5. Adjust the flame to the desired level by turning the Thumb Wheel (7) counterclockwise. (See Figure A.) 6. NOTE: The lit Blow Torch should operate with a blue flame with a small yellow tip. If necessary, adjust the Thumb Wheel (7) if there is sputtering or popping. (See Figure A.) THUMB WHEEL (7) PIEZO BUTTON (16) BURNER (1) CYLINDER CONNECTOR (11) FIGURE A SKU 91061 PAGE 6 7. To extinguish the flame, close the Thumb Wheel (7) by turning it completely clockwise. (See Figure A.) 8. Allow sufficient time for the Blow Torch to completely cool. Then, store the Blow Torch in a safe location and out of reach of children. INSPECTION, MAINTENANCE, AND CLEANING 1. Before each use, inspect the general condition of the Blow Torch. Check the Blow Torch for loose connections and joints, cracked, bent, or broken parts, damaged propane bottle, and any other condition that may affect the safe operation of the Blow Torch. If a problem occurs, have the problem corrected before further use. Do not use damaged equipment. 2. When cleaning, use only water and a mild detergent. Do not use cleaners that are combustible or corrosive. 3. When storing, always allow sufficient time for the Blow Torch to completely cool down before storing. Do not store flammable liquids or materials in the area surrounding the Blow Torch. Make sure the Blow Torch’s Tumb Wheel (7) is in its “OFF” position. PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUAL...


Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie