valutazioni - , GPA:
(
)
)
Produttore : Sunbeam
File Size : 372.75 kb
File Nome : f23072cb-8828-485c-bb78-5fd2328323d9.pdf
Lingua di insegnamento: 
Il documento viene caricato, si prega di attendere
 |
Il documento viene caricato, si prega di attendere
Facilità d'uso
The tank may overflow and boiling water may be emitted from the nozzle instead of steam. Using the Eco Jet Ensure the unit is unplugged from the power outlet before fitting or changing attachments. 1.Fit the desired attachment following the instructions on page 9. 2.Insert the plug into a 230/240V power outlet and turn the power on. The light near the base of the unit will illuminate, indicating that the steam boiler is heating. Once the light goes out (approx. 3 -4 minutes), the Eco Jet has reached the optimum temperature for producing steam and is ready to use. 3.Direct the Eco Jet at the desired surface and depress the steam trigger on the handle. 4.Slowly move the Eco Jet back and forth over the surface to be cleaned. To remove stubborn stains, hold the unit over the area for several seconds. 5.Once you have finished cleaning the desired area remove the plug from the power outlet. 6.Allow the unit to cool completely before storing. Caution: Do not tilt the Eco Jet more than 45 degrees from the horizontal or turn it upside down during or immediately after use. Boiling water could come out of the nozzle instead of steam. Filling the Eco Jet during use Do not unscrew the water tank cap until the following steps have been followed. 1.Unplug the power cord form the outlet. 2.Remove any remaining steam from the water tank by depressing the steam trigger until the tank is completely empty. 3.Partially unscrew the water tank cap, waiting five minutes for any remaining steam to escape and to allow the unit to cool down. Proceed to completely unscrew the cap. 4.Carefully empty any remaining water from the water tank. Caution: Water will be extermely hot. Note: Always ensure that the water tank is completely empty before refilling the Eco Jet to avoid overfilling. Do not exceed the maximum water level. 5.Slowly refill with 300ml (max) of clean tap water using the jug and funnel provided. Measure using the 150ml mark on the side of the measuring jug. Repeat. 6.Replace the cap and tighten. Using your Eco Jet continued Fitting the attachments Before removing any attachment, ensure the plug is disconnected from the power outlet. Always allow the unit and the attachment to cool completely before handling. Fitting the standard nozzle 1.Attach the standard nozzle to the Eco Jet by pushing it onto the steam outlet, aligning the arrow engraved on the attachment with the join line above the steam outlet. Turn the attachment in the direction of the arrow until it locks into place and the arrow on the attachment aligns with the double line marked on the side of the steam outlet. 2.To remove the standard nozzle, twist the attachment back against the direction of the arrow. When the arrow engraved on the attachment is aligned with the join line above the steam outlet, pull the attachment firmly to remove. Fitting the utility head and fabric cloth 1.Fit the fabric cloth to the utility head by stretching the elasticised cloth over it, ensuring it is evenly fitted and quite snug. Note: Do not use the utility head without a cloth attached as this may cause damage to surfaces. 2.Attach the utility head with cloth to the Eco Jet by pushing it onto the steam outlet aligning the arrow engraved on the attachment with the join line above the steam outlet. Turn the attachment in the direction of the arrow until it locks into place and the arrow on the attachment aligns with the double line marked on the side of the steam outlet. Note: When cleaning large areas the cloth may become quite wet and/or dirty. Switch the unit off at the outlet, wait for the attachment and the cloth to cool completely before removing the cloth to rinse, wring out and replace. Alternatively replace with a clean, dry cloth. 3.To remove the utility head, twist the attachment back against the direction of the arrow. When the arrow engraved on the attachment is aligned with the join line above the steam outlet, pull the attachment firmly to remove. Fitting the utility head and squeegee The squeegee works in conjunction with the utility head and needs to be attached to it before being mounted to the unit. 1.Fit the squeegee to the utility head by aligning the hooks on the squeegee with the holes on the utility head. 2.Push the top of the utility head down so that it is secured under the clip on the top of the squeegee. 3.Attach the utility head with squeegee to the Eco Jet by pushing it onto the steam outlet aligning the arrow engraved on the attachment with the join line above the steam outlet. Turn the attachment in the direction of the arrow until it locks into place and the arrow on the attachment aligns with the double line marked on the side of the steam outlet. 4.To remove the squeegee from the utility head lift the clip on the top of the squeegee up and pull away from the utility head. Using your Eco Jet continued Fitting the round brush The round brush can be used in conjunction with the standard nozzle, the flexible extension nozzle or fitted directly to the...