valutazioni - 3, GPA: 3.7
(
)
)
|
Facilità d'uso
Dukane Audio Visual Products • 800-676-2485 • AirSlate AS2 070016 Page 1 Dukane AirSlate (AS2) Fast Start User Guide Please read all instructions carefully before attempting to connect your Bluetooth Tablet. TIP: Do Not connect 2 USB Bluetooth Adapters (Dongles) to one computer. Do not connect the USB adapter (dongle) when an internal Bluetooth is operating. This will result in a conflict and neither will work. Thank you for purchasing this product. The Dukane AirSlate, AS2, can be connected two ways to a computer. These are via a cable or wireless using a Bluetooth radio link. This manual will first describe the wireless Bluetooth connection. Section 1 – Battery Installation for Slate & Pen 1. Charge the AA batteries 24 hours prior to using or start with 2 fresh AA Alkaline batteries. 2. Batteries must be charged in pairs (up to 4 at a time). 3. Insert the two AA batteries into the underside battery compartment of the slate. The compartment is accessed by moving the tab towards the center of the tablet. A “+” is located on the plastic inside the compartment to show battery orientation. 4. Turn on the power switch. With the tablet facing up, the on/off switch is located in the upper left hand corner. The red indicator lamp should light for a few seconds and then go “off”. 5. Place one AAA battery into the pen. The pen can ONLY be used with a AAA alkaline type battery. The “+” terminal of the battery is toward the tip of the pen. When the pen battery needs to be replaced, the pen LED indicator will light. LED Indicator Information for the SLATE There are dual color LED’s located just above the top left of the macrokey area. One is Red and the other is Blue. Operation in Wireless Bluetooth mode: 1. When the Bluetooth Tablet is turned on, the dual Red LED will flash once. 2. When the battery power is low, the Red LED will start to flash until the batteries are exhausted. Please change the batteries once the Red LED starts flashing. 3. The Blue LED will flash continuously when the Slate is linked to the computer. 4. The Blue LED will be on continuously when the pen is detected 1.2” above the working area, but will go off when the pen touches the tablet. Operation in Wired USB mode (Cable connecting the Slate to the computer): 1. When the USB cable is initially connected to the Tablet, the Red LED will flash once and the Blue LED will flash continuously. 2. The Blue LED will be on when the pen is detected above the working area but will go “off” when the pen touches the tablet. Function Bluetooth Mode USB Cable Mode Power On (Bluetooth Mode) Red flash once Red flash once USB cable plugged in (USB mode) Blue flash once Blue flash continously Working/Linked Tablet to PC Blue flash continously Blue flash continously Pen above working area Blue light Blue light Pen tip on the working area of tablet off off Low batteries in tablet Red light/Red flashing -- Page 2 Dukane Audio Visual Products • • AirSlate AS2 070016 Section 2 – Software Installation For Windows XP, Service Pack 2 Only (If other Windows Program Go to page 13 for Windows 2000 or Windows XP Service Pack 1). (To identify which Service Pack is installed, see Appendix A). Wireless mode (using the Bluetooth link): 1. Insert the “Bluetooth Tablet” CD and click on the “Bluetooth Pen Pad Manager”. Follow the installation procedure. Click on “Next”. Click “Finish”. 2. Next add the Bluetooth Software. Caution; BE SURE THAT THE BT ADAPTER (DONGLE) IS NOT PLUGGED INTO THE USB PORT. This also assumes that the PC does not have an internal operating Bluetooth Radio that would be in conflict with the dongle. 3. Click on “ Bluetooth Dongle Driver (XP SP2)”. After data for Microsoft Bluetooth software is loaded click “Finish”. 4. The CD-ROM tray will open. Remove the CD from the tray. 5. Now plug the Bluetooth Dongle in the USB port. 6. The “Found New Hardware will appear. This will be followed by the appearance of the “Found New Hardware Wizard”. 7. Check the “Yes this time only” box. Then “Next”. The software will be installed and a Bluetooth Icon will appear in the lower right tray. 8. The install runs on automatically and the “Found New Hardware, Microsoft Bluetooth Enumerator” will appear. The “Wizard” will next appear. Check “Install the software automatically”, then “Next”. And then “Finish”. Check to see that the Bluetooth Icon located in the lower right tray by the clock is white with a blue background. 9 Activating the Bluetooth connection. (Paring the PC and the slate). 9.1 Turn “On” the slate. Put pen in holder or keep it away from the slate. 9.2 Press and hold the “Disconnect/Unpairing button” for 5 seconds. 9.3 Go to the PC Start/Settings/Control Panel. Click on “Bluetooth Devices” 9.4 On the “Bluetooth Devices/Options” check all the boxes in “Discovery” and “Connections” then click “OK.” 9.5 Go to the “Devices” tab. Click on “Add”. Step 9.5 9.6 The “Add Bluetooth Device Wizard” window appears. Check box “ My device is set up and ready to...