valutazioni - 4, GPA: 4.3
(
)
)
|
Facilità d'uso
D DIGITAL IN OPT connectors (11) (14) Connect a digital optical cable to input digital signals from other components. There is no distinction of OPT1 and OPT2 connectors. E DIGITAL OUT COAXIAL jack (11) Connect a digital coaxial cable to output digital signals to other components. F DIGITAL OUT OPTICAL connector (11) Connect a digital optical cable to output digital signals to other components. G CONTROL A1.. jacks (11) (44) 9 GB Display window description/Rear panel description Getting Started This chapter provides information on the supplied accessories and hookups. Be sure to read this chapter thoroughly before you actually connect any equipment to the deck. Before you start the hookup Checking the supplied accessories This MD deck comes with the following items: • Audio connecting cords (2) • Remote commander (remote) (1) • R6 (size-AA) batteries (2) Inserting batteries into the remote Insert two R6 (size-AA) batteries into the battery compartment with the + and – properly oriented to the markings. When using the remote, point it at the remote sensor on the deck. z When to replace the batteries Under normal conditions, the batteries should last for about six months. When the remote no longer operates the deck, replace both batteries with new ones. Notes • Do not leave the remote in an extremely hot or humid place. • Do not drop any foreign object into the remote casing, particularly when replacing the batteries. • Do not use a new battery with an old one. • Do not expose the remote sensor to direct sunlight or lighting apparatus. Doing so may cause a malfunction. • If you don’t use the remote for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion. GB 10 Before you start the hookup Hooking up the audio components CONTROL A1.. AC power cord ACBDAmplifier, etc. CD player, DBS tuner, etc.1), Digital amplifier, DAT deck, MD deck, etc.2) to a wall outlet Getting Started 1) Digital equipment with a DIGITAL OUT connector only 2) Digital equipment with both DIGITAL IN and OUT connectors Required cords A Audio connecting cords (2) (supplied) When connecting an audio connecting cord, be sure to match the color-coded pins to the appropriate jacks: white (left) to white and red (right) to red. White (L) White (L) Red (R) Red (R) B Optical cables (3) (not supplied) • When connecting an optical cable, take the caps off the connectors and insert the cable plugs straight in until they click into place. • Do not bend or tie the optical cables. C Coaxial digital connecting cables (2) (not supplied) Hookup considerations • Turn off the power of all components before making any connections. • Do not connect any AC power cord until all the connections are completed. • Be sure the connections are firm to prevent hum and noise. Jacks (connectors) for connecting audio components Connect To the Amplifiers ANALOG IN/OUT jacks CD players or DBS tuners DIGITAL IN connector Digital amplifiers, DAT decks, or another MD deck DIGITAL IN/OUT connectors 11 GB Hooking up the audio components Getting Started Other connections To connect a CONTROL A1.. compatible component D Monaural (2P) mini-plug cables (2) (not supplied) For details, see “Using the CONTROL A1.. control system” on page 44. To connect the AC power cord Connect the AC power cord of the deck to a wall outlet. Note If you use a timer, connect the AC power cord to the outlet of the timer. Demonstration mode When you turn on the MD deck and there is no MD in the deck, demonstration mode is activated automatically after about ten minutes. To deactivate the demonstration mode, press any button on the deck or on the remote. z To turn off the demonstration mode Press x and CLEAR simultaneously when there is no MD in the deck. “Demo Off” appears in the display. To turn on the demonstration mode again, perform the same procedure described above. “Demo On” appears in the display. Setting the clock Once you set the MD deck’s internal clock, the MD deck will automatically record the date and time of all recordings. For USA and Canadian models, date is displayed in the order of month, day, year, and time on a 12-hour clock. For European model, date is displayed in the order of day, month, year, and time on a 24-hour clock. Note The display windows below are of USA and Canadian models. 1 twice. 2 til “ AMSMENU/NO YES m/M 3 Turn AMS (or press ./> repeatedly) to enter the current day, then press AMS. The month (or day) indication stops flashing, and the day (or month) indication starts flashing. 4 Repeat step 3 to enter the month, day, year, hour, and minute. . Complete!! . . Changing the clock setting(s) 1 Do steps 1 and 2 above. 2 Press AMS or m/M repeatedly until the setting you want to change flashes. GB 12 Hooking up the audio components/Setting the clock 3 Turn AMS (or press ./> repeatedly) to change the setting, then press AMS. 4 To complete the setting, press AMS or m/M repeatedly until the minute indica...