valutazioni - 5, GPA: 4.6
(
)
)
|
Facilità d'uso
A track number is created in the middle A track number may be created if there are scratches or dust on the of a track. MiniDisc. 45 IM- DR400E TINSE0562AWZZ 03/7/ 21 IM-DR400E_ 6.fm IM- DR400E Error Messages ReferencesError Messages A number or symbol appears in (*) position. ERROR MESSAGES MEANING BATT EMPTY • The battery has run down. BLANK MD • Nothing is recorded. (Replace the disc with a recorded disc. ) Can't COPY • You tried to record from a copy prohibited MiniDisc. (Record using the analogue cable. ) • You tried to record signals other than music ( such as data) . Can't EDIT • A track cannot be edited. (Change the stop position of the track and then edit it. ) Can't LOCK • You tried to remove the MD whilst recording or editing. Can't PLAY • You tried to play back a track that cannot be played with this equipment. Can't READ (*) • The disc data cannot be read because the disc is damaged. (Reload the Minidisc or replace it with another one. ) Can't REC • Recording cannot be performed correctly due to vibration or shock. ERROR MESSAGES MEANING Can'tSTAMP • Stamp function does not work. (Check the number of tracks. ) Can'tWRITE • Cannot save the TOC information correctly to a MiniDisc. DEFECT! • The disc is scratched. (If the recorded sound is not right, retry recording or replace the disc with a recordable one. ) DISC FULL • The disc is out of recording space. Er-MD (**) • The microprocessor has reported a system fault and the unit is out of order. (To have it repaired, go to the distributor where you purchased the unit. ) HOLD • The unit is in the hold mode. LOCKED • You removed a MiniDisc whilst recording or editing. (Turn off the power before removing the MiniDisc. ) NO DISC • A disc has not been loaded. IM- DR400E TINSE0562AWZZ 03/7/ 21 IM-DR400E_ 6.fm IM- DR400E ERROR MESSAGES MEANING NO SIGNAL • Poor connection of the digital cable. • No output signal comes out from the connected unit. (Use the AC power for the connected unit. ) • The input signal has improper sampling frequency. PLAY MD • You tried to record on a playback- only disc. POWER? • AC adaptor other than specified. PROTECTED • The write protection tab of a MiniDisc is set to the protected position. SORRY • Since a track number is currently being located or updated, the unit cannot accept your command. (Wait a while and try the operation again. ) ERROR MESSAGES MEANING TEMP OVER • The temperature is too high. (Turn off the power, and wait a while. ) TOC FORM (**) • There is an error in the recording signal. (Erase all of the tracks, and then record again. ) TOC FULL • There is no space left for recording character information (track names, disc names, etc. ) . Tr. Protect • The track has been protected from being erased. (Edit the track with the device on which it was recorded. ) ? DISC • A disc which contains data other than music was played. (A disc which contains nonmusic data cannot be played. ) • There is an error in the signal recorded on the disc. A number or symbol appears in ( * ) position. ReferencesError Messages 47 IM- DR400E TINSE0562AWZZ 03/7/ 21 IM-DR400E_ 6.fm IM- DR400E Troubleshooting References-Troubleshooting- Many potential "problems" can be resolved by the owner without calling a service technician. If something seems to be wrong with this product, check the following before calling your authorised SHARP dealer or service centre. The unit does not turn on. • Is the AC adaptor disconnected? • Is the battery exhausted? • Is the unit in the hold mode? • Has condensation formed inside the unit? • Is the unit being influenced by mechanical shock or by static electricity? Recording and editing are impossible. • Is the MiniDisc protected against accidental erasure? • Is the unit connected properly to the other equipment? • Is the AC adaptor unplugged or did a power failure occur whilst recording or editing? • Is the unit in the hold mode? • Is an optical signal being output from the stereo system? Read the operation manual for the stereo system. The operation is unstable whilst the PC and the unit are connected. • Are you using the USB cable that was purchased separately? The display does not show anything or malfunctions. • Is the PC out of order? • Are you using another application with this programme simultaneously? Editing is not possible. • Are the PC and the MD portable recorder connected improperly? • Is the MD recorder in the hold mode? • Is a commercial playback- only MD inserted? No sound is heard from the earphones. • Is the volume set too low? • Are the earphones plugged in? • Are you trying to play a MiniDisc with data on it instead of a MiniDisc containing music? When the operation buttons are pressed, the unit does not respond. • Is the unit in the hold mode? • Is the battery exhausted? • Is the earphones plug inserted firmly? Some sounds are skipped. • Is the battery exhausted? • Is the unit being subjected to excessive vibration? The MiniDisc cannot be ejected. • Has the track number or character inform...