3.) Turn the TUNING control to find the desired station. PROGRAM REPEAT RANDOM POWER FM ST. The FM ST. indicator light comes ‘On’If you PM tune to a FM Stereo station, . AL. 1 AL. 2 4.) Adjust the VOLUME control to the desired level. 5.) When you are finished listening press the POWER button to turn the unit ‘Off’. PROGRAM REPEAT RANDOM POWER FM ST. The POWER indicator goes ‘Off’. PM AL. 1 AL. 2 11 CKD1137_053105.p65 11 1/6/2005, 14:22 Antenna Information AM The AM ferrite bar antenna is inside

Press the CD OPEN button to open the CD door and remove your disc. To Start Playback From A Specific Track Load your disc and wait until the display shows the total number of tracks. Press the or buttons to select the desired track. While the track number is still flashing press the PLAY/PAUSE button. Playback will begin on the selected track and continue until the end of the disc. High Speed Music Search You can search rapidly forward or backward within a track to locate a specific musical pass

For purchasing this Emerson Personal CD Player. It has a 24 track programmable memory so you can listen to the songs on your favorite CD's in any order you choose. Or you can use the Random playback feature and let the player select the playback order for you. Use the 3-way Repeat feature to repeat a single track, the entire disc, or a programmed sequence of tracks, indefinitely. We've also included a 45 Second Electronic Anti-Skip Memory which makes this player virtually skip- free under normal

If the display is blank press the PLAY/PAUSE button to start the disc. When playback begins press the STOP button. If the disc was playing, press the STOP button so that the total tracks and playing time appear on the display. 1. While the total tracks and playing time appear on the display press the PROG (Program) button. "PROG" indicator flashes and Program No. "P - 01" appears. 2. Press SKIP FWD or SKIP REV button until the first track to be programmed appears in the display. Example: Track #

11 HD7090_ib072902.p65 11 29/7/2002, 18:33 INTRO SCAN This feature plays only the first 10 seconds of each track on the disc. 1.) At stop mode press the MODE button 3 times. The “INT”indicator appears in the display. 2.) Press PLAY/PAUSE button to begin playback. 3.) The player begins track 1 and plays just the first 10 seconds of each track on the disc. When the first 10 seconds of each track has been played, the player stops. To cancel Intro Scan press the STOP button or press the MODE button

The “PROG” indicator stops flashing and remains in the display. The player will play the tracks you selected in the programmed order. When the last track has played the player stops and the total tracks and playing time appear. 6.) To cancel programmed playback press the STOP button twice. The program mm will also be canceled if the CD Door is opened or if the power is interrupted. 10 HD7096A_7099A_071403.p65 10 14/7/2003, 10:34 “JOGGABLE” ELECTRONIC ANTI-SKIP PROTECTION This CD player is equipp

We've also included a 60 Second Joggable Anti-Skip Memory which makes this player virtually skip-free during most active uses. There's a Dynamic Bass Boost Control that increases and enhances the bass response and a set of digital quality, lightweight stereo headphones. Please read this instruction manual completely and carefully to make sure you understand the proper operation of this product, and get the maximum enjoyment out of all the features of this state-of-the-art CD, CD-R/RW player. Onc

Replacing The Batteries When the battery symbol flashes in the display the batteries are becoming weak and should be replaced. 4.) Close the battery door, and press the door down make sure fully locked again. 5.) Close the CD door. Always replace both batteries at the same time with new fresh alkaline batteries. Do not mix old and new batteries or different types of batteries together. If the display remains blank when you press the PLAY/PAUSE button, the batteries are completely dead. Replace t

NOTE: Make sure the headphone plug is inserted into the headphone jack as far as it will go. If the plug is not fully inserted, you may only hear sound from one side of the headphones. IMPORTANT! Always set the VOLUME control to a low level before you put the headphones on and begin playing a CD. Then start playback and gradually increase the volume to a comfortable listening level. Do not play the CD at loud volume levels that might prevent you from hearing warning sounds such as car horns, etc