valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
and grounding outlet. Properly polarized I_ Three-prong (Grounding plug) CAUTION l Before you begin installing the oven, PLACE A PIECE OF THE CARTON OR OTHER HEAVY MATERIAL (a blanket) over the countertop or cooktop to protect it. Do not use a plastic cover. Failure to protect these surfaces could result in property damage. FTK-127i130 Buitt-in Trim Kit installation instructions For use with the following microwave oven ACM2160A and UMC5200AA hetallation of Bottom Bracket 1= Disconnect power from microwave oven before proceeding with installation= 2= Remove any loose items from inside the microwave oven, 3. Fasten bottom bracket to bottom duct using 1/2"screws (supplied). 4. Turn microwave upside down and place on a protected surface. Fo_ oq Fr°nt _o \\ ____l 5= Attach bottom duct to bottom of microwave using 1/2Tscrews (supplied)= 6= Turn microwave oven and bracket right side up, placing it on a protected surface. hetaHation of Vented Ductwork 1= Remove screw located on left side of microwave below vent louvers. 2= Secure side duct to upper duct, by inserting metal tabs on upper duct into slots on side duct and bending tabs upward as indicated in the following illustration= Upper Tabs duct 3= Remove any oil or dirt on the surface of the microwave oven where ductwork will be secured. 4= Peel off the protected backing on the double sided tape. 5= Place the existing screw through the ductwork and start securing the screw DO NOT TIGHTEN. Slowly push the ductwork towards the microwave keeping proper alignment of the ductwork= Press down firmly to secure the ductwork and tighten the screw securely. Existin_._ screw Preparing for Anti-Tip Bracket 1= Fold or cut the edges from the template a!ong the guide lines. 2= Place the template along the front edge of the cutout floor, centering the template from sideStoSside= 3= Mark the hole positions of the antiStip bracket. 4= Remove the template and drill two holes for antiStip bracket. Use a drill bit no larger than 7/64tto make holes= 5= Place antiStip bracket onto the cutout floor and secure using 1/2"screws. 1/2" screws Side Anti-tip bracket duct FTK-127/130 Buitt-in Trim Kit installation instructions For use with the following microwave oven ACM2160A and UMC5200AA hstaHing Unit in Cutout 1, Slide microwave oven into cutout verifying alignment of unit is correct, 2, Slide unit out to plug the power cord into the outlet, 3, Slide unit into cutout centering the microwave oven in the cutout opening, Verify anti=tip bracket is engaged, Bottom duct Bottom bracket bracket 4. Ensure the microwave oven is accurately centered after verifying the anti4ip bracket is engaged. 5. Using a 7/64;drill bit dri!l pilot holes through the positioning flange into wood or metal framing and secure with 1/2"screws in the bottom duct. / Mounting Trim Frame 1. Position trim frame over the microwave oven, 2. Verify trim frame is level and the microwave oven is centered within the trim frame. NOTE: Center the trim frame equally on aH four sides, 3. Mark center positions screw holes (one in each corner) through the mounting holes of the trim frame. 4. Remove trim frame and drill previously marked pilot holes using a 1/16;drill bit. 5. Attach trim frame to wood or metal frame work using 1" screws (supplied). Trim kit is completed Replace any loose items that were removed from the inside of the microwave, Retain installation instructions for future reference. 112" screws Trim Frame Dimensions < 26-7/8" > Depth of the trim frame is 7is". < 29-3/4" 1-7/16" I 2-7/8" 19-1/8" 19-1/8" 30" -Trim Frame 27" -Trim Frame Part No.8101P555-60 Part No.3828W5U0295 ...
Questo manuale è adatto anche per i modelli :Piastra - FTK-127 (395.47 kb)