valutazioni - 2, GPA: 3.5 ( )

Produttore : Dimplex File Size : 6.72 mb File Nome : Lingua di insegnamento:

Although the main lights operate immediately it will take a further 30 seconds before the fl ame eff ect starts. Press again to give fl ame effect and half heat. This will be indicated by two beeps. Press again to give fl ame effect and full heat. This will be indicated by three beeps. Press again to return to fl ame eff ect only. This will be indicated by one beep. Press to put stove in to standby mode. This will be indicated by one beep. Control Knob ‘C’:- Controls the intensity of the fl ame eff ect. Turning the control knob to the left increases the fl ame effect, turning the control knob to the right will decrease the fl ame eff ect. Control Knob ‘D’:- Controls the Electronic Thermostat setting. Turning the control knob to the left will decrease the temperature setting, turning the control knob to the right will increase the temperature setting. When the water is empty the main lamps go out. See instructions under ‘Maintenance’, ‘Filling the water tank’. When this procedure is complete, the main lamps will illuminate but it will take 30 seconds before the fl ames return. Depending on room temperature and humidity there may be some condensation on the inside of the stove. This can be overcome by turning the flame control knob down and leaving the doors of the stove slightly ajar, until the glass warms up. Electronic Thermostat The thermostat controls the heat output according to the room temperature. This ensures that the stove will not produce heat unnecessarily when the room is warm. To set the temperature you require, turn the thermostat control knob ‘D’ (See Fig. 2) to the right until the desired temperature is reached. Alternatively to heat a cold room quickly, turn the thermostat control knob ‘D’ (See Fig. 2) up fully. When the room has reached the desired temperature, turn the thermostat control knob ‘D’ (See Fig. 2) to the left until the desired heat setting is achieved. The stove will now automatically operate at this temperature. Remote Control Operation On the control panel, Switch A (see Fig. 2) must be in the ‘ON’ ( I ) position in order for the remote control to operate. There are 3 buttons on the remote control. (See Fig. 7) To operate correctly the remote must be pointed towards the front fuel eff ect. The remote control functions are as follows: Press once to turn on Flame eff ect only. This will be indicated by one beep. Press once to turn on Half heat and Flame eff ect. This will be indicated by two beeps. Press again to turn on Full heat and Flame eff ect. This will be indicated by three beeps. Standby This will be indicated by one beep. - 2 Battery Information. Maintenance 1. Unclip the battery cover on the back of the remote control. (See Fig. 7) 2. Install AAA batteries into the remote control. 3. Replace the battery cover. Discard leaky batteries. Dispose of batteries in the proper manner according to provincial and local regulations. Any battery may leak electrolyte if mixed with a diff erent battery type, if inserted incorrectly, if all the batteries are not replaced at the same time, if disposed of in a fire, or if an attempt is made to charge a battery not intended to be recharged. Thermal safety cut-out A thermal safety cut-out is incorporated in the fan stove to prevent damage due to overheating. This can happen if the heat outlet was restricted in any way or if the chimney flue has not been blocked off effectively. If the cut-out operates, unplug the stove from the socket outlet and allow approximately 10 minutes before reconnecting. Before switching the stove back on remove any obstruction that may be restricting the heat outlet, then continue normal operation. Tips for using your appliance. 1. Only pull out the drawer when its time to refi ll the water tank or change a lamp, otherwise it may lead to excess water in the sump and reduced fl ame eff ect. If this happens empty the water from the sump as instructed under ‘Maintenance’. 2. With the flame setting on minimum the unit will use approximately 40ml of water per hour and will last 3 times as long than when it is at maximum fl ame setting. 3. Do not tilt or move the stove while there is water in the tank or sump. 4. Make sure that the stove is on a level fl oor. 5. The flame control knob ‘C’ Fig. 2 may be turned up or down to give a more realistic eff ect. 6. Sometimes the flames appear more real when the flame control knob is turned down. 7. Give the flame generator some time to react to changes you may make on the flame control knob. WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE Changing lamps. If a large amount of the smoke appears grey or colourless it may be that one or more lamps have failed. You can check for lamp failure as follows. 1. Leaving the fl ame effect on, open the doors fully, gently pull the drawer fully out by the tab. (See Fig. 3) 2. View the lamps from a distance in front of the stove and observe which lamp needs to be changed. 3. Put Switch ‘A’ in the ‘OFF’ p...

Scarica la tua

Per scaricare, digitare 2 cifre :