|
Facilità d'uso
The fireplace and chimney should be cleaned thoroughly before starting the installation. We suggest painting the interior of particularly old and dirty fireplaces to seal any odors. In zero-clearance fireplace installations, when the fireplace opening is above the floor or raised hearth, the adjustable “Breckwell P24 Z-C Skirt” (part # A-ZC-SKRT), or “Breckwell P24 Z-C Legs” (part #A-S-ZCLEGS), can be used to bridge the gap between the hearth and stove bottom. (Refer to figure 13) A. ASSEMBLING THE FLASHING SET Follow the instructions packaged with the P24 Flashing set part C-P24-MEDFL-C or C-P24-LGFL-C. (Refer to Figure 14) FIGURE 13 FIGURE 14 INSTALLATION12 INSTALLATION12 B. WHEN VENT PIPE EXTENDS TO CHIMNEY TOP (Refer to Figure 15) 1. You will need a pipe length equal to the chimney height (from hearth) plus 6 inches. If outside combustion air is to be used, you will need a pipe length (see “COMBUSTION AIR SUPPLY”) equal to the chimney height plus 12 inches. 2. Attach cerablanket wrap to the end of vent pipe that will connect to the stove. Use 12inch lengths of light gauge metal wire (not included) or metallic tape (not included). This is to protect interior components from excess heat. 3. Set the insert on the hearth and slide it in far enough to attach the vent pipe (and combustion pipe if used). 4. Attach flashing (refer to Figure 14), route power cord out the side nearest a 120V receptacle. Slide in insert. 5. Measure and build chimney top. Cut out hole for vent pipe (and combustion air intake pipe, if used). Install and seal with a non- hardening mastic to prevent water leakage. Install the vent cap. C. WHEN VENT PIPE EXTENDS THROUGH CHIMNEY BLANKING PLATE (Masonry Fireplaces Only) (Refer to Figure 15) 1. You will need a pipe length that extends 12” above the blanking plate. NOTE: This installation is optional but not recommended. Outside combustion air cannot be drawn from the chimney cavity in this installation. 2. Attach cerablanket wrap to that end of vent pipe that will connect to the stove. Use 12inch lengths of light gauge metal wire (not included) or metallic tape. This is to protect interior components from excess heat. 3. Measure and build blanking plate. Cut out hole for vent pipe (and combustion air intake pipe, if used). Install and carefully seal blanking plate with non-hardening mastic. Failure to properly seal may result in smoke spillage. 4. Slide vent pipe (and intake pipe if used) up through the blanking plate hole, leaving enough to pull back down. 5. Set the insert on the hearth, adjust the leveling bolts on the rear sides, and slide it in far enough to attach the vent pipe (and combustion air pipe if used). Be sure to seal where the pipe passes through the blanking plate. 6. Attach flashing (refer to Figure 14), route power cord out the side nearest a 120V receptacle. Slide in insert. FIGURE 15 INSTALLATION 13 INSTALLATION 13 D. AS A BUILT-IN FIREPLACE Figures 16 and 17 describe a P24 installation vented into either a special chase built outside an outer wall or a false inside wall. This is especially suited for new construction or remodeling. The equipment compartment (sides and rear of the stove in fireplace) must be enclosed per the applicable electrical standards. NOTE: Floor protection for Built-in raised hearths requires a continuous sheet beneath to prevent the possibility of embers falling through to the combustible floor if cracks or separation should occur in the finished surface. The chase dimensions shown are minimums and must be maintained. FIGURE 16 FIGURE 17 INSTALLATION14 INSTALLATION14 E. INSTALLATION IN TO A FACTORY BUILT (METAL) FIREPLACE (Refer to figure 18) When installing into a factory built fireplace, the firebox must accept the insert without modification other than removing bolted or screwed together pieces such as smoke shelf/deflectors, ash lips, screen or door tracks and damper assemblies. These items must be reinstalled to restore the fireplace to its original operating condition if the insert is removed and not replaced. The removal of any part must not alter the integrity of the listed fireplace in any way. In zero-clearance fireplace installations, when the fireplace opening is above the floor or raised hearth, the adjustable “Breckwell P24 Z-C skirt” (part # A-ZCSKRT), or “Breckwell P24 Z-C Legs” (part #A-SZCLEGS), can be used to bridge the gap between the hearth and stove bottom. (Refer to figure 13) The factory built fireplace must be listed per UL 127. Installation must include a full height listed chimney liner meeting type HT requirements (2100° F) per 1777 (U.S.). The liner must be securely attached to the insert flue collar and the chimney top. The damper area must be sealed to prevent room air passage to chimney cavity. Alteration of the fireplace in any manner is not permitted except with the following exceptions: • External trim pieces, which do not affect the operation of the fireplace, may be removed proving they can be stored on or...
Questo manuale è adatto anche per i modelli :Piastra - P24FS (744.59 kb)