valutazioni - 1, GPA: 3
(
)
)
|
Facilità d'uso
appear on the receiver’s display), position the remote sensor and main unit within the effective transmission range of HOW TO USE THE TABLE STAND 100 feet. The main unit has a removable table stand, which supports NOTE: the unit on the flat surface. The main unit can also be 1. Avoid setting the time and date on the main unit before the mounted on the wall using the recessed screw hole. outdoor temperature is displayed. The stand must be removed prior to mounting. The remote 2. The effective operating range may be influenced by the sensor can be similarly mounted or placed on a flat surface. surrounding building materials and how the receiver and transmitter are positioned. 3. Position the remote sensor so that it faces the main unit GETTING STARTED (receiver), minimizing obstructions such as doors, walls, After batteries are installed, remote sensors will transmit and furniture. temperature readings at 45 second intervals. The main unit4. Though the remote sensors are weather-resistant, they may take up to 2 (two) minutes to receive the initial readings. . should be placed away from direct sunlight, rain or snow. Upon successful reception, remote temperature will bedisplayed. Then the main unit will automatically update BATTERY INSTALLATION readings at 45-second intervals. REMOTE SENSOR NOTE: Install the batteries; select the channel and type ofIf no signals are received from the remote sensor(s) withintemperature (.C/.F) before you mount the sensor.(2) two minutes, dashes “ ” will be displayed. 1. Remove the screws from the battery compartment with a Press and hold [ ] button on the main unit for 2 seconds small Phillips screwdriver. to initiate another signal search. 2. Set the channel. The switch is located in the battery . compartment. Channel 1 is typically selected if 78 10 9 READING THE KINETIC WAVE DISPLAY The kinetic wave display shows the main unit (receiver) signal reception strength. MAXIMUM AND MINIMUM TEMPERATURE & HUMIDITY The maximum and minimum records of the indoor/outdoortemperature and humidity will be automatically storedin the memory of the main unit (receiver). Main unitwill display the minimum, maximum and the current readingupon each press of MEM button. The unit will return to the current temperature display in 15 seconds. To clear the memory, press and hold MEM button and stored readings will be erased. TEMPERATURE TRENDS The temperature trend indicator shows the trend oftemperatures collected at particular remote sight. There arethree trends will be shown: rising, steady, and falling. COMFORT LEVEL INDICATORS The comfort level indicators COM, WET or DRY will tell you if the current environment is comfortable, too wet ortoo dry. The comfort indicators will appear on the displayof the main unit when the following conditions are satisfied: The unit is in searching mode. Temperature readingssecurely registered. No signals. °F TREND TREND Arrow indicator TemperatureTrend Steady Falling Rising TREND CHECKING REMOTE AND INDOOR TEMPERATURES The wave icon on the main unit's display located near theremote sensor reading line, indicates a good reception fromthe remote sensor. If the temperature goes above or below thetemperature operating range stated in specifications, thedisplay will show dashes “ ” WWVB RADIO CONTROLLED TIME The NIST (National Institute of Standards and Technology) radio station is located in Ft. Collins Colorado. It transmits an exact time signal continuously throughout the continentalUnited States at 60 KHz frequency. The Weather Forecastercan receive this WWVB signal through its internal antennafrom up to 2,000 miles away. Due to the nature of the Earth’sionosphere, reception can be limited during the daylight hours. The radio controlled clock will search for an alternate station that derives its signal from the NIST Atomic clock in Boulder, Colorado. * Make sure the main unit is positioned at 8 feet minimum distance from any interference source such as a TV, computer monitor, microwave, etc. The successful reception of the atomic time signal depends on the positioning and location of the clock. Always place the main unit by the window for better reception. * Within concrete wall rooms such as basements or office buildings, the received signal may be weakened. Always place the unit near the window. The WWVB tower icon on the main unit’s display will flashindicating radio signal reception from the WWVB station. If the tower icon is not fully lit, or if the time is not setautomatically, please consider the following: * During night-time hours, atmospheric disturbances are typically less severe and reception may improve. A single daily reception is sufficient enough to keep the accuracy reading within 1 second. 10 9 READING THE KINETIC WAVE DISPLAY The kinetic wave display shows the main unit (receiver) signal reception strength. MAXIMUM AND MINIMUM TEMPERATURE & HUMIDITY The maximum and minimum records of the indoor/outdoortemperature and humidity will be automatically...
Questo manuale è adatto anche per i modelli :Stazione Meteo - TE529ELW (2.07 mb)