Log:
valutazioni - 4, GPA: 3.5 ( )

Istruzioni per l'uso Taylor, Modello 1527

Produttore : Taylor
File Size : 1.15 mb
File Nome : 1527_ib.pdf
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


Simple, reliable, accurate…it allows you to monitor indoor or outdoor locations from one room. The base unit reads indoor conditions, while the remote sensor wirelessly reports outdoor weather conditions back to the base unit for an all-in-one weather display. Plan your work day, play day, every day. Now that’s smart! Table of Contents Powering theWeatherGuide™..................................................................3 How to Set Up the WeatherGuide™ ......................................................3 How to Display the WeatherGuide™ ......................................................5 Atomic Clock Atomic Clock Setting ................................................................6 Manual Clock Setting..................................................................7 Alarm ............................................................................................8 Snooze ........................................................................................10 How to Read the WeatherGuide™........................................................11 Temperature/Humidity Displays ............................................12 Minimum/Maximum Records ................................................13 Barometric Pressure ................................................................14 History Records........................................................................14 Programming Altitude ..............................................................15 Comfort Level Readings..........................................................16 Temperature/Humidity Trends ..............................................16 Weather Forecast ....................................................................17 Backlight......................................................................................18 °F/°C Switch ..............................................................................18 Low Battery Display ................................................................18 TroubleShooting Disconnected Signals................................................................19 Transmission Collision ............................................................20 Problem Solving ........................................................................20 Precautions ................................................................................21 2 To Power your WeatherGuide™ Base Unit Your WeatherGuide™ base unit may be powered by either an AC adaptor (included) or 2 AAA batteries (not included). Adaptor power – insert the connector end of the adaptor into the jack on the side of the base unit. Plug the other end into the proper electrical outlet. Battery Power – Remove the battery compartment cover on the back of the unit. Install 2 AAA batteries. Replace the battery compartment cover. Important: Power the base unit before installing batteries in the re- mote sensor, or the units’ transmissions may not properly connect. Remote Sensor Unscrew the 4 screws securing the remote sensor’s battery compart- ment cover located on the back of the unit. Install 2 AAA batteries. (Tip: Lithium batteries are recommended in extremely cold or hot lo- cations.) How to Set up Your WeatherGuide™ System First, power up the base unit, using either the AC adaptor or 2 AAA batteries. Next, install 2 AAA batteries into the remote sensor. Place the base unit as close as possible to the remote unit. Movechannelswitch There is a Channel switch in the remote sensor battery compartment. Move the switch to Channel 1. to Channel 1 Press the “TX” button located inside the remote sensor battery compartment.This will send a transmission signal to the base unit.The red LED Indicator light will flash when a signal is transmitted. Press the Tx button to send transmission signal to base unit 3 TransmissionsuccessfulTransmissionsuccessful If the transmission is successful,the remote sensor readings and a “ ” icon will appear on the base unit. If dashes are still displayed on the receiver unit, press the Tx button again. To change the remote sensor’s tempera- ture display to Celsius, press the “+C/F” button inside the remote’s battery com- partment. Replace the remote’s battery compart- Select °F or °C for remote ment cover. The remote will automatically transmit readings to the base unit. • The first remote registered will transmit every 53 seconds. • If a second remote is registered, it will transmit every 56 seconds. • If a third remote is registered, it will transmit every 59 seconds. Note: A maximum of 3 remote sensor units can be registered. Should you purchase one or two additional remote units (Model 1536, sold separately) to expand your thermometer monitoring capabilities to multiple locations, slide the CH switch to Channel 2 to register the second sensor and select Channel 3 to register the third sensor.The Channel number assigned will appear on the remote’s LCD screen. 4 How to Display your WeatherGuide™ Table top – use th...


Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie