valutazioni - 4, GPA: 3.3 ( )

Produttore : Snapper File Size : 1.19 mb File Nome : Lingua di insegnamento:

26 PIN, Clevis, 3/8 x 4" 2 27 BUCKET, Material, 38" or 48" wide 1 ASSEMBLY INSTRUCTIONS NOTE: Leave all attaching hardware loose until the loader is completely assembled to facilitate assembly and ; proper loader alignment. INSTALLING LOADER SIDE FRAMES 1. Place 5/8 x 3-1/4 pins (21) into the hole in side frame mounting hooks (23). Fasten hooks (23) to side frames (12 & 13) with 1/2 x 3/4 serrated head cap screws (20), but do not tighten. 2. Position hinges (17) inside of side frames. Install 5/8 x 3-3/4 carriage bolts (19) as shown and secure with lock nuts (14). 3. Position side frames over the loader mounting brackets and clamp hinges (17) around tube of mid mounting bracket. Install 5/8 x 3" cap screws (18), flat washers (16) and elastic lock nuts (15), but do not tighten. Raise side frame hook pins (21) and secure with 2-11/16 hair cotter pins (22). See page 12 for reference. INSTALLING FRONT BUMPER 1. Attach front bumper (25) to side frames (12 & 13) with 3/8 x 4" clevis pins (26) and 1-7/8 hair cotter pins (24). INSTALLING GREASE FITTINGS 1. Install 1 /4 straight grease fittings (5) into the tube at the rod end of each lift and bucket cylinders. Install 1/4 x 45° grease fittings (11) pointing up into the tube at the end of lift boom frame arm. Install 1/4 straight grease fittings (5) into bucket pins (8). INSTALLING LIFT BOOM FRAME 1. Attach lift boom frame (1) and lift cylinders into side frame uprights with 3/4 x 3-1/4 pins (9), 3/8 x 1" shoulder bolts (10) and lock nuts (2). 2. With the loader centered on the tractor mounting brackets, securely tighten hinges (17) around mid mounting bracket. 3. Slide side frame mounting hooks (23) against front mounting bracket tubes to properly position hooks, then securely tighten 1/2 x 3/4. serrated cap screw (20). INSTALLING BUCKET 1. Attach bucket to the lift boom frame and bucket cylinders with 3/4 x 3-1/4 pins (7, 8 & 9), 3/8 x 1". shoulder bolts (10) and lock nuts (2). INSTALLING BUCKET LEVEL INDICATOR 1. Attach indicator guide tube (3) to the bucket cylinder mount on the left side of lift boom frame with 3/8 lock nuts (2). NOTE: Leave lock nuts loose enough so tube rotates freely. 2. Slide bucket level indicator rod (4) into the guide tube and attach the other end of rod to bucket cylinder pin (7) with 5/32 x 1-1/2 cotter pin (6). 3. Locate tractor and loader on level surface. With the bottom of bucket resting on surface, cut off the, excess rod (4) flush with the end of guide tube (3). . F-2486-12,-86 25 ASSEMBLY & PARTS ... .... . . I 26 F-2486-12-86 ASSEMBLY & PARTS PARTS LIST — VALVE, PUMP & PLUMBING KIT I Item_Description ______Qty. ! 1 PIN, Hair Cotter, 3/32 x 1-7/8 2 ! 2 SPROCKET, W/Spline Hub, #40B12 1 3_CHAIN, Roller, #40-2 x 12 Pitches_______1 4 ! SPROCKET, W/Keyway Hub, #40B12 1 5 FITTING, Elbow Adaptor, 3/4-3/8 x 90° 2 6 FITTING, Elbow Adaptor, 3/8-3/8 x 90° 1 7 NUT, Lock, 3/8-16 2- 8 HOSE, 3/8 x 72" I 9 Y-STRAINER I 10 PLUG, Pipe, 3/8 ~~ “ --j- 11 FITTING, Adaptor, 1/2-I/2 1 12 FITTING, Adaptor Union, 7/8-1/2 1 13 PUMP, Parker Model D14AA2A 1 14 SCREW, Set, Socket Head, 1/4-20 x 1/4 or 10-24 x 1/4 1 1 5_BRACKET, Pump M ounting_1 16 SCREW, Cap, 3/8-16 x 1-1/4 * 2 17 STRAP, Adjustable Tie „ 3 _J8_HOSE, 1/2 x 48" ■_;___1_ 19 FITTING, Elbow Adaptor, I/2-1/2 x 90° 1 20 FILTER ASSEMBLY 1 _21_FITTING, Adaptor, 3/8-3/8_._I_ 22 FITTING, Elbow Adaptor, 1/2-3/8 x 90° 1 i 23 NUT, Hex, 1/4-20 2 2 4_WASHER, Lock, 1/4___2 25 VALVE, Dukes Fluid Power Model 1627 DM 1 26 HOSE, 3/8 x 14" 1 2 7_FITTING, Adaptor Union, 3/4-3/8 x 45°__1 28 PIN, 1/4 x 3/4 2 29 U-HOOK 2 3 0_PIN, Cotter, 1/16 x 1/2 4 31 HANDLE, Valve 2 32 SCREW, Cap, 1/4-20 x 2-1/4 2 3 3_FITTING, Adaptor, 9/16-9/16_ 4 ' 34 HOSE, 1/4 x 22-1/2 2 35 HOSE, 1/4 x 20" 2 36 CAP, Breather 1 37 FITTING, Street Elbow, 1/2 x 90° I 38 PLUG, Pipe, 1/4 ,1 39-_KEY, Woodruff, 1/8 x 5/8 Diameter_ _ ' j ASSEMBLY INSTRUCTIONS INSTALLING TWO LEVER VALVE 1. Install 1/2 x 90°street elbow fitting (37) to upper port 3. Attach valve handles (31) to the valve spools with 1/4 x located at the rear of left side frame. 3/4 pins (28) and 1/16 x 1/2 cotter pins (30). Fasten valve handles to the valve mounting bracket with u-hooks (29) 2. Fasten valve (25) to the valve mounting bracket on side and 1/16 x 1/2 cotter pins (30). frame with 1/4 x 2-1/4 cap screw (32), lock washers (24), and nuts (23). F-2486-9-93 27 ASSEMBLY & PARTS PLUMBING TWO LEVER VALVE TO LOADER 1. Install 1/2 x 3/8 x 90° elbow fitting (22) into the upper port located on inside of left side frame. Install 3/8 - 3/8 straight fitting (21) onto the outlet port of filter base (20). Install the other end of fitting (21) into elbow fitting (22). Install 3/8 x 14” hose (26) to inlet port of filter base (20). Install filter element into filter base. 2. Install 3/4 - 3/8 x 90° elbow fitting (5) into the outlet of valve. Install 3/4 - 3/8 x 45° elbow fitting (27) into the inlet port of valve. Co...

Scarica la tua

Per scaricare, digitare 2 cifre :