DCR-4 LRHD-7 (Rakes shown with optional gauge wheels) 3 PT. LANDSCAPE RAKE Safety Instructions Assembly & Mounting Tractor Preparation Maintenance Operating Instructions Repair Parts CAUTION THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE THOROUGHLY UNDERSTOOD BEFORE ATTEMPTING TO BEGIN ASSEMBLING THIS MACHINE 1. Select an area for assembly that is clean and free of any 6. After completing assembly, thoroughly inspect the debris which might cause persons working on the machine to be sure that all nut

Hydraulic system leak down, hydraulic system failures, mechanical failures, or movement of control levers can cause equipment to drop or rotate unexpectedly and cause severe injury or death. • Service work does not require going underneath. • Read Manual for service instructions or have service performed by a qualified dealer. WARNING! Keep all persons away from operator control area while performing adjustments, service, or maintenance. Before dismounting power unit or performing any service or

Position the tongue weldment between the front pull brackets welded to the front crosstube. Install the two 5/8” x 11/2” bolts with washers and nylock nuts as shown in the exploded parts diagram. NOTE: Nylock nuts are used at locations where some pivoting motion is expected between the bolted parts. It is suggested that nylock nuts be tightened to just a snug fit and then backed off 1 - 11/2 turns. Install the two 1/2”x 31/2” shift pins to lock the tongue weldment to the front crosstube pull bra

Periodically tighten all bolts, nuts and screws and check that all cotter pins are properly installed to ensure unit is in a safe condition. When completing a maintenance or service function, make sure all safety shields and devices are installed before placing unit in service. Never use your hands to locate a hydraulic leak on attachments. Use a small piece of cardboard or wood. Hydraulic fluid escaping under pressure can penetrate the skin. Openings in the skin and minor cuts are susceptible t

Keep load low. WARNING! For multiple spear models, always insert spears into the bale – NEVER under the bale. Failure to insert spears into bale can allow bale to roll back when loader is raised, causing serious injury or death. TRANSPORTING —————————————————— CAUTION! When traveling on public roads, whether at night or during the day, use accessory light and devices for adequate warnings to operators of other vehicles. Comply with all federal, state and local laws. Carry load low. Check visibil

WARNING! For multiple spear Models GLB-3000, GLB-330, GLB-340, always insert spears into the bale – NEVER under the bale. Failure to insert spears into bale can allow bale to roll back when loader is raised, causing serious injury or death. Always use a tractor and front loader large enough to safely handle your bales. Check your tractor and front loader to make sure they are in good working condition. Check all loader mounting bolts to make sure they are tight. Check the tractor’s hydraulic sys

Be sure tractor is properly counter-balanced with weights before attempting to lift any load with the Bale Spear attachment. If you are handling bales with both the front end loader and the 3 pt. hitch on the tractor, always load the 3 pt. attachment first and unload last. The bale spear is to be used only for handling hay bales. Do not use for digging rocks, pulling out fence, or as a craning device with a chain over the spear. LARGE ROUND BALES: Using the bucket tilt cylinders, adjust the angl

Stop loader gradually when lowering or lifting loads. 8 SAFETY INSTRUCTIONS (continued) OPERATIONAL SAFETY (continued) Allow for additional length of loader and bale on tractor while turning. Never allow anyone to walk or work under a raised loader. Do not use loader for a work platform. Do not lift or carry anyone on loader or in bucket or on attachment. Set both front and rear tractor wheels wide for increased stability. Be sure that people, livestock, or pets are not standing near the machine

If its ability to do a job, or to do so safely, is in question – DON’T TRY IT. Do not modify the equipment in any way. Unauthorized modification may impair the function and/or safety and could affect the life of the equipment. In addition to the design and configuration of this implement, including Safety Signs and Safety Equipment, hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper training of personnel involved in the operation, transport, ma

Keep foldable ROPS systems in “locked up” position at all times. Operate only in daylight or good artificial light. Always check to be sure the loader attachment is properly latched on the loader or that lock pins are installed. Ensure that all safety shielding and safety signs are properly installed and in good condition. Never permit any person other than the operator to ride or board the tractor or implement at any time. ALLOW NO RIDERS! The use of any loader attachment is NOT recommended on