Log:
valutazioni - 3, GPA: 4.3 ( )

Istruzioni per l'uso Amana, Modello 685000800012

Produttore : Amana
File Size : 427.04 kb
File Nome : 685000800012.pdf
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


At first fill, approximately 1 minute make sure water completely covers filter surface. . At pump-out: (pump-out is either when the cycle is completed or canceled. refer to the Use and Care Manual for Start/Cancel), make sure all water is pumped out. Check water connections again for leaks. Electric Shock Hazard If all connections are correct, there are no leaks, and unit runs properly, replace the kickplate assembly before placing unit into operation. Failure to follow this warning could result in electric shock. check these items: . Water and drain lines have no kinks and move freely behind the dishwasher. . Water supply is turned on. . Joints are free of leaks. . Wiring connections to junction box are tight all access panels are secured back in place. . Replace kickplate and kickplate brace. (See Figure 1) . Drain hose is assembled to Drain Hose Connector. . All packing materials and consumer literature have been removed from inside unit. . Dishwasher is level and securely fastened. . Open and close door to make sure it does not hit surrounding cabinet or countertop. 1. Review Figures 7, 8 and 9 to see the different ways to connect dishwasher to drain system. Choose method that best suits your need. 5. If the cabinet wall is wood, sand edges of hole until smooth and rounded. If cabinet wall is metal, cover all sharp edges with electrical or duct tape to avoid cutting drain hose. Entry Must be Above Trap Sink at Left Sink at Right “Y” Branch Tailpiece 2” Drain Hose Hole Sink at Right Remove Knockout Plug in Disposer 2” Drain Hose Hole Figure 9(b) 3. If you connect to a sink trap, local codes may require you to install an air gap kit, (not included). The drain hose will be routed from dishwasher to air gap inlet as shown in Figure 8. An air gap kit is available from a plumbing supply store. (If the drain hose is installed through the floor, an air gap is necessary). 4. If you connect to a disposer, the large end of drain hose will fit. Figure 9(a). The knock out plug must be removed from inside disposer inlet before making the final fit to drain hose. See Figure 9(b). Air Gap Right Side Installation Drain Air Gap Sink at Left Alternate Drain Through Floor into Separate Trap 2. If you connect to a sink drain, entry will need to be above trap. A “Y” branch tailpiece and connector kit, not included, will make this method easier and includes all needed fittings and instructions. See Figure 7. Figure 8 Figure 7 Finishing the Drain 7 Connection 6. Move unit back in place while routing drain hose through access hole. Use caution to prevent damage to the dishwasher, floor and cabinets. IMPORTANT: Make sure there are no sharp bends or kinks that might restrict drain flow. 7. Secure drain hose to sink drain, disposer, or separate trap with a clamp. IMPORTANT: Be careful not to overtighten clamp or you may damage end of hose. Do not connect hose to horizontal pipe between sink drain and disposer. 8. Be sure unit does not rest on drain hose. It should be free of electrical components and door springs. Do not cut corrugated drain hose. Pull excess through cabinet and place under sink. Make sure hose does not come in contact with any sharp edges. The drain hose loop must be at...

Questo manuale è adatto anche per i modelli :
Lavastoviglie - 685000800012 (427.04 kb)
Lavastoviglie - 685000800012 (427.04 kb)
Lavastoviglie - 685000800012 (427.04 kb)
Lavastoviglie - 685000800012 (427.04 kb)

Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie