valutazioni - 3, GPA: 3.7
(
)
)
|
Facilità d'uso
Your Direct Feed Wash System dishwasher uses energy efficient motors for the wash and drain portions of the cycle you select. Each cycle has a series of water fills and drains for washing and rinsing dishes. As each cycle begins, you may–or may not– hear the drain motor. The next sound you will hear is the splashing water as it enters the tub. PLEASE BE ADVISED: If you compare this dishwasher to previous models, you may be surprised at what you DON'T hear! DISHWASHER FEATURES Your dishwasher cleans by spraying a mixture of hot water and detergent through the spray arms against soiled surfaces. Each cycle begins by filling with water covering the filter area. Next, the dishwasher fills with water covering the filter area. Water is then pumped through the filter and spray arms. Soil particles go down the drain as the water is pumped out and replaced with clean water. The number of water fills will vary with the cycle being used. Heating Element Glass Trap Self-Cleaning Filter Rinse Aid Dispenser Upper Spray ArmTub Gasket Middle Spray Arm Lower Spray Arm Detergent Dispenser Top Rack Serial Label (located on right side of tub) Bottom Rack Silverware Basket Adjustable Upper Rack Cup Shelf Bowl Tines OPERATING INSTRUCTIONS Getting Started 1. Load dishwasher (See Preparing and Loading Dishes). 2. Add detergent (See Dishwasher Dispenser & Detergents). 3. Add rinse aid (See Rinse Aid). 4. Select desired CYCLE (See Cycle Chart). The indicator light above the pad will glow when selected. 5. Select desired OPTIONS (See Energy Options). The indicator light above the pad will glow when selected. 6. Run hot water faucet nearest dishwasher until water is hot. Turn water off. 7. To start, press START/CANCEL pad. 8. Close door to latch. NOTE The dishwasher is programmed to remember your last cycle so you do not have to reset each time. To start the dishwasher using the same cycle and options selected on the previous wash, just press the START/CANCEL pad. Wash Cycle Selections Cycle times are approximate and will vary with options selected. Hot water is necessary to activate dishwasher detergent and melt fatty food soils. An automatic sensor will check the incoming water temperature and, if it is not hot enough, the timer will be delayed for automatic water heating in the main wash of all cycles. This happens even when HI-TEMP WASH option has not been selected. When HI-TEMP WASH is selected, an even higher temperature will be guaranteed to handle heavier soil loads. NOTE Lights and Display on top of console will shut off when the door is closed. They will light up when the door is opened and display time remaining will be displayed for several seconds. Then “Cd” will display flashing, informing you to close the door so the cycle can continue. Options Selections Hi-Temp Wash When HI-TEMP WASH option is selected, the dishwasher heats water in the main wash to approximately 140°F (60°C). This increase in water temperature helps dishwasher detergent remove food grease and soil from dishes more effectively and aids in drying. This option is available in NORMAL WASH and LIGHT WASH. HI-TEMP WASH is automatically provided when HEAVY WASH cycle is selected. OPERATING INSTRUCTIONS Sanitize Option To sanitize your dishes and glassware, select the SANITIZE option. When selected, the light above the pad will come on. The water temperature in the final rinse will be raised to 155°F (68°C) assuring bacteria is destroyed. This option is available in HEAVY WASH, NORMAL WASH and LIGHT WASH. Only these sanitization cycles have been designed to meet NSF requirements. The cycle time will be extended until the proper water temperature is reached.Washing action will continue during the water heating delay. For best results, the incoming water temperature should be at least 120°F (49°C). The sanitize criteria may not be satisfied if there is an interruption of the cycle, power failure or if the incoming water temperature is below 120°F (49°C). To turn off the SANITIZE option, press the pad a second time. The light above the pad will turn off. To Cancel a Cycle You can cancel a cycle anytime during the cycle. Press START/CANCEL pad and the dishwasher will start a 60 second drain. At the end of the drain, select the desired cycle. When an option is selected, the light above the pad will come on and remain on until end of cycle. To turn off the option, press the pad a second time. The light above the pad will turn off. Child Lock Controls To prevent children from accidently changing the dishwasher cycle or starting the dishwasher, lock the dishwasher controls by pressing and releasing the DELAY START pad for 3 seconds. An indicator light on the lock graphic pad will illuminate when the controls are locked and no new selections can be made until the lock is released. To unlock the controls, press the DELAY START pad until the indicator light goes out. Air Dry The unit defaults to heated dry when it is started with any cycle selected. This drying uses a ...