valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
4. To deactivate the audible signals, press again the function push button 3, the "end of programme" indicator light turns off, indicating that the audible signals have been deactivated. 5. To memorise the operation, switch off the dishwasher by pressing the On/Off push button or wait about 60 seconds after which the dishwasher will automatically return to setting mode. Operating instructions Prior to using for the first time Before using your dishwasher for the first time: 1. Ensure that the electrical and water connections comply with the installation instructions 2. Remove all packaging from inside the appliance 3. Set the water softener 4. Pour 1 litre of water inside the salt container and then fill with salt 5. Fill the rinse aid dispenser. Setting the water softener The dishwasher is equipped with a water softener designed to remove minerals and salts from the water supply, which would have a detrimental or adverse effect on the operation of the appliance. The higher the content of these salts, the harder your water is. Water hardness is measured in equivalent scales, German degrees, French degrees and mmol/l (millimol per litre). The softener should be adjusted according to the hardness of the water in your area. Your local Water Authority can advise you on the hardness of the water in your area. The water softener must be set in both ways: manually, using the water hardness switch and electronically, using the function push buttons on the control panel. Water hardness Adjusting the water hardness setting Number of flashes and of audible signals °dH (german degrees) °TH (french degrees) mmol/l (millimol per litre, international unit for the hardness of water) Range Manually Electronically 51 - 70 43 - 50 37 - 42 29 - 36 23 - 28 91 - 125 76 - 90 65 - 75 51 - 64 40 - 50 9,0 - 12,5 7,6 - 8,9 6,5 - 7,5 5,1 - 6,4 4,0 - 5,0 IV 2 10 9 8 7 6 10 9 8 7 6 19 - 22 15 - 18 33 - 39 26 - 32 3,3 - 3,9 2,6 - 3,2 III 5 4 5 4 1 11 - 14 19 - 25 1,9 - 2,5 II 3 3 4 - 10 7 - 18 0,7 - 1,8 I/II 2 2 < 4 < 7 < 0,7 I 1 no salt necessary 1 a) Setting manually 1. Open the dishwasher door. 2. Remove the lower basket from the dishwasher. 3. Turn the water hardness switch to position 1 or 2 (see table). 4. Replace the lower basket. The dishwasher is factory set at position 2. b) Setting electronically (The dishwasher must be switched off) The dishwasher is factory set at level 5. 1. Press the On/Off push button. All programme selection push buttons indicator lights will illuminate (setting mode). If only one programme selection push button indicator light is illuminated, this means that a washing programme has been selected. The programme must be cancelled: press simultaneously the function push buttons 2 and 3 for about 2 seconds, the indicator light of the setted programme push button starts flashing for about 2 seconds. After about 2 seconds the indicator lights of all the programme selection push buttons will illuminate indicating that the setted programme has been cancelled and that the machine is now in setting mode. 2. Press simultaneously function push buttons 2 and 3, until the indicator lights of the function push buttons 1, 2 and 3 start flashing. 3. Press the function push button 1, the indicator lights of function push buttons 2 and 3 turn off while the indicator light of the push button 1 goes on flashing, at the same time the "end of programme" indicator light illuminates, along with a sequence of audible signals. The current level is indicated by the number of flashes of the "end of programme" indicator light and of audible signals heard. Example: 5 flashes + 5 audible signals = level 5. Operating instructions 11 AA07 Operating instructions 4. To change the level, press push button 1. Each time the push button is pressed the level changes. (For the selection of the new level see the chart). Examples: if the current level is 5, by pressing push button 1 once, level 6 is selected. if the current level is 10, by pressing push button 1 once, level 1 is selected. 5. To memorise the operation, switch off the dishwasher by pressing the On/Off push button or wait about 60 seconds after which the dishwasher will automatically return to setting mode. Operating instructions Filling the with salt Only use salt specifically designed for use in dishwashers. All other types of salt not specifically designed for use in a dishwasher, especially table salt, will damage the water softener. Only fill with salt just before starting one of the complete washing programmes. This will prevent any grains of salt or salty water, which may have been spilt, remaining on the bottom of the machine for any period of time, which may cause corrosion. To fill: 1. Open the door, remove the lower basket and unscrew the cap of the salt container by turning it anticlockwise. 2. Pour 1 litre of water inside the container (this is necessary only before filling with salt for the first time). 3. Using the funnel provided, pour in the salt until the container...