valutazioni - 3, GPA: 3.3
(
)
)
|
Facilità d'uso
Do not use an extension lead or multiple plug for connection to the electrical socket. . If your dishwasher is underneath a work surface with a hob. You must add thermal insulation to the top of the machine. 4 ADJUSTING THE FEET... It is essential that the door is closed and latched before stabilising the dishwasher. Ensure that the rear feet are adjusted so that the product is not sitting on the base of the machine. Adjust either clockwise or anti-clockwise as necessary to level. Then adjust either of the two front feet clockwise or anti-clockwise as necessary until all feet are in contact with the floor to avoid the machine from rocking and is level to within 2° Note: If the appliance is not levelled the door may be off centre and make the machine unstable. Page 5 FP105-01 DWF35/34/33/30 12/02/2002 10:22 am Installation... CONNECT TO A DRAINAGE SYSTEM... WARNING . Connect your dishwasher drain hose to pipes which connect to the foul drain system and not to surface water drains. IMPORTANT NOTES For the correct operation of your dishwasher, it is essential to comply with the following information. Standpipe Fit the hose to the standpipe hook which can be found in the machine. Ensure that the hose is not pushed too far down the standpipe. DO NOT position the standpipe near an electrical outlet. 120 min ENSURE that the drain hose is routed as shown in the diagram. The standpipe should be connected to: a) A discharge stack-pipe b) An external gulley OR c) A sink waste. The standpipe should have a bore of at least 38mm (11/2"). It should be installed as shown, have a trap fitted and must discharge into the same drain system as your household sink. It must NOT be connected to a surface water drain. Sink Waste System For under sink drainage: Before connecting the drain hose, remove any internal restrictions - This will prevent a build up of debris which could cause a blockage. Remove any restrictions from the waste spigot and ensure that the sealing bung is removed. The hose should be routed, such that it is raised to a minimum height of 800mm (31/2"). 1. Untie the end of the GREY drainage hose from the rear of the appliance. 2. Reposition ‘Hooked End Support’ as required along GREY drainage hose. 3. If fitting an under sink waste disposal unit, cut out the membrane, bung or blanking plug. 4. Attach the GREY drainage hose to the under sink waste disposal unit securely, using the clip and rubber tube supplied. Note: Ensure the sink outlet pipe has a minimum diameter of 32mm (11/4"). Ensure the drain hose is securely attached, to prevent it coming away while the machine is in use and causing a flood. 5 Page 6 FP105-01 DWF35/34/33/30 12/02/2002 10:22 am Installation... CONNECT TO THE WATER SUPPLY... . For your machine to operate correctly it requires water pressures in the range of 6-150 psi (100-1000 KPa). Most cold water supplies will be in this range. . Note: Low water pressure will lead to excessively long fill times or no fill. . Ensure that the new hose supplied is connected and the old hose is disposed of safely. . Ensure the fill hose is only connected to the cold water supply. WARNING . Ensure the fill hose is NOT kinked. Note: Do not over tighten the hose connector. Hand tight is sufficient. . Tap connections (if applicable) - A range of adaptors are available to suit your tap. WARNING . Do not connect appliance to a single outlet instantaneous water heater or an electric heater. Remember you may be charged for a service call if a problem with your appliance is caused by incorrect installation or misuse. 6 CHECKLIST... When you have installed your appliance, ensure it is ready to use by following this Check List: 1. Dispose of packaging safely, see ‘Recycling Information’ on page 2. 2. Position appliance close to electrical/water supply see ‘Choose a Location’ on page 4. 3. Connect supplied hose to appliance water supply, confirm water is flowing before connecting to the appliance inlet valve see ‘Connect to a Water Supply’, page 6. 4. Untie drainage hose at rear of appliance and connect to either a standpipe or sink waste drainage system see ‘Connect to a Drainage System’ page 5. 5. Untie mains lead at rear of appliance and plug into electrical supply via a switched socket, see ‘Electrical Supply’ on page 3. 6. Position appliance, taking care not to kink or damage hose at rear of appliance. 7. Stabilise the appliance, see ‘Adjusting the Feet’ page 4. 8. Turn on the water supply to the appliance. 9. Switch on at plug socket. Your appliance is now ready for use, refer to ‘Getting to know your Appliance’ on page 7 to familiarise yourself with the appliance. FP105-01 DWF35/34/33/30 12/02/2002 10:23 am Page 7 Getting to Know your Appliance... 1 76 9 1182 3 4 5 DWF35 DWF34 DWF33 and DWF30 1 76 82 3 4 511 1 1062 3 4 511 8. Time Delay Selection Button ) (DWF35 / 34 only) 9. Half Load Selection Button (for Upper Basket washing) (DWF35 only) 10. Programme End Light (DWF33 / 30 only) 11. Programme End Buttons (Reset...
Questo manuale è adatto anche per i modelli :Lavastoviglie - DWF33 (546.6 kb)
Lavastoviglie - DWF34 (546.6 kb)
Lavastoviglie - DWF35 (546.6 kb)