valutazioni - 4, GPA: 4
(
)
)
|
Facilità d'uso
If necessary, fit a syphon trap (U-bend) with a connecting piece for the drain hose (fig.B). The free end of the hose must be at a height between 40 and 100 cm and must not be immersed in water. fig.B Attention: The connecting piece for syphon trap (U-bend) must be solidly fastened to the wall to prevent the drain hose from moving and allowing water to spill outside the drain. Electrical Connection After making sure that the voltage and frequency values for your home correspond to those on the rating plate (located on the stainless steel inner door of the appliance) and that the electrical system is correct for the maximum voltage on the rating plate, insert the plug into an electrical socket which is earthed properly (the earthing of the appliance is a safety requirement mandated by law). If the electrical socket to which the appliance must be connected is not appropriate for the plug, replace the whole cable, rather than using adaptors or the like as they could cause overheating and burns. Caution: The dishwasher plug must be accessible even when the appliance is installed as a built-in unit so that maintenance can be done safely. Getting to know your dishwasher EN Close-up view (control panel) Dishwasher interior A C B A ON-OFF Button C Programme Indicator B Programme Button How to fill the salt Salt The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will form on the dishes and utensils. The appliance is equipped with a special softener that uses a salt specifically designed to eliminate lime and minerals from the water. Loading the salt into the container Always use salt intended for use with dishwashers. The salt container is located beneath the lower rack and should be filled as follows: According to the “Water Hardness Tabel”, you can calculate the salt consumption setting, then load the salt . Remove the lower rack and then unscrew and remove the cap from the salt container. If you are filling the container for the first time, fill it with 1/2 a litre of water. Place the end of the funnel (supplied) into the hole and fill with about 2 kg of salt. It is normal for a small amount of water to come out of the salt container. Carefully screw the cap back on. Do not over tighten it. Important To prevent the formation of rust, load the salt just before beginning a wash cycle. a d e f h b c i j k g a Upper Rack g Washing Filter b Lower Rack h Detergent and Rinse Aid Dispenser c Top Spray Arm i Water Inlet Hose d Silverware Basket j Drain Hose e Bottom Spray Arm k Power Supply Cord f Salt Container Cap Adjusting salt consumption The dishwasher is designed to allow for adjusting the amount of salt consumed based on the hardness of the water used. This is intended to optimize the amount of salt consumption keeping it to a minimum. To adjust salt consumption, proceed as follows: Unscrew the cap from the salt container; There is a ring on the container with an arrow on it (see figure below ). If necessary, rotate the ring in an anticlockwise direction from the "-" setting towards the "+" sign, based on the hardness of the water being used. It is recommended that adjustments be made in accordance with the following table: Water Hardness Level Clarke degrees .dH mmol/l Selector position Salt consumption (Grams/cycle) Autonomy (cycles/2kg) 1 014 MNT MNIT L M L 2 NQPS NUQQ NIUQIQ =?J? OM SM 3 PSTN QRUV QIRUIV jba QM QM 4 [TN [UV [UIV ?H? SM OR How to fill rinse aid EN Rinse aid This product makes dishes sparkle and helps them to dry without spotting. The dispenser is located on the inside panel of the door . When the low rinse aid indicator “ 1 ” is bright ,it means the rinse aid is low,you must refill the rinse aid dispenser.. 2 3 1 Low Full How to fill the detergent dispenser Detergent Detergent specifically intended for use with dishwashers must be used. The dispenser must be refilled before the start of each wash cycle following the instructions provided in the "Programme overview". The detergent dispenser is located on the inside panel of the door. 5 4 6 7 Not suitable for the dishwasher What you should not put into the dishwasher Cutlery and tableware manufactured in whole or part from wood.They become faded and unsightly in appearance.Furthermore,the adhesives that are used are not suitable for the temperature that occur inside the dishwasher.Delicate decorative glassware and vases,special antique or irreplaceable china. The decorative patterns on such items will not be dishwasher-proof. Plastic objects that are not resistant to hot water, copper and pewter utensils are also not suitable. Decorative patterns printed or painted onto the surface of crockery, glasses, etc.,aluminium and silver items tend to become discoloured or faded if washed in the diswasher. Some types of glass can become opaque in appearance after they have been washed many times in a dishwasher. Highly absorbent materials, such as sponges and towels,should never be placed in the dishwash...
Questo manuale è adatto anche per i modelli :Lavastoviglie - DW12-PE1ME (262.7 kb)
Lavastoviglie - DW12-PFE1SS (262.7 kb)