valutazioni - 2, GPA: 5 ( )

Produttore : Equator File Size : 740.52 kb File Nome : Lingua di insegnamento:

.Clear restrictions. .Replace drain pump. .Replace circuit board. Water siphons out. .Drain hose loop to low. . Drain line connected to a floor drain not vented. .Move to proper height. .Install vent air gap at counter top. Water leaks. .Spray arm not rotating or split. . Check for proper rotation or replace spray arm. 11 . Overcharge of water. .Tub seal (torn, worn or loose). . Dishwasher door not sealing properly. .Dishwasher is not level. . Overburden (wrong type of detergent). .Hose clamps loose. . Heater element mounting nuts loose. .Water seal leaking. .O-ring is not in position. . Motor and pump assembly not seated proper in tub liner bottom. .Check and correct for proper fill. .Replace tub seal. . Adjust door latch assembly and/or strike. .Level dishwasher properly. .Instructs customer/user. .Tighten all clamps securely. .Tighten the nut. .Use a new water seal. .Adjust the ring or replace a new. .Replace seal. Poor wash ability. .Spray arm not rotating. .Improper loading of dishes, pans and other. .Detergent dispenser inoperative. .Insufficient amount of detergent. Or the detergent is old. .Damaged or the impeller is broken. .Detergent not dissolve. .Check for proper rotation. . Instructs customer/user on proper loading per owner’s guide. .Repair or replace dispenser. .On proper amount of fresh deter gent to use. .Replace pump assembly. .Incoming water temperature of 140 °F is required to proper dissolve detergent. Poor drying of dishes .Improper loading of dishes, pots and other. .Heating element (open). .Incoming water temperature too low. . Wiring or terminal (broken or burnt). . Instruct customer/user on proper loading per owner’ s guide. .Replace heating element. .Incoming water temperature of 140°F for best drying results. .Replace or repair. Detergent cup will not open. .Cup binding. .Roll pin retainer or shaft broken. .Defective bi-metal. .Timer contact (open or broken). .Repair or replace. .Replace pin, retainer or shaft. .Repair or replace. .Replace timer. Door will not lath. .Door latch damaged. .Replace door latch. Rinse agent liquid will not eject. .Electromagnetic valve defective. .Rinse agent dispenser not mounted correctly. .Plunger stuck or held in closed position. .Replace valve. .Mount securely to rear of inner door panel. .Free plunger or adjust plunger release. Rinse agent liquid leaks. .Container cracker or broken. .Replace container. 12 .Defective seal on plunger. .Over filling container. .Replace plunger. . Follow instructions in owner’s manual. Noisy pump assembly. .Impellers not properly shimmed or rubbing. .Pump parts not properly installed. .Debris in bottom of tub sump area. .Defective motor bearings. . Use shim gauge furnished in impeller and seal kit, when seals are properly shimmed the impellers will be in correct operating position. .Inspect and correct. .Clean out sump area. .Replace motor. Dishwasher continues to fill or continues to fill even though in case of there is no voltage to fill valve. . Something (dirt or foreign material) under diaphragm in water inlet valve. .Defective water inlet fill valve. . Clean water inlet valve or replace. .Replace water inlet valve. Detergent left in dispenser. .Detergent cup held or blocked by large dishes. . Dispenser wet when detergent was added. .On proper loading dishes. .Instructs customer/user. Softener leaking .Softener broken. .Softener nut loosen. .Replace softener. .Screw down softener cap. Leaking form air inlet. .Air inlet nut loose. .Air inlet install up side down. .Screw down air inlet nut. .Reinstall air inlet properly. Window Display “E1” .Inlet Valve Damaged. .Inlet Valve Disconnected. .Replace Inlet Valve. .Reconnected Line. Window Display “E2” .Pressure Switch Damaged. .Replace Pressure Switch. Window D...

Scarica la tua

Per scaricare, digitare 2 cifre :