valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
Start the appliance without utensils in the programme with the highest rinsing temperature. Clean the appliance with detergents/ appliance cleaners which are particularly suitable for use with dishwashers. – Regularly clean door seal with a damp cloth. Never use a steam cleaner to clean your dishwasher. The manufacturer is not liable for any consequential damage. Regularly wipe the front of the appliance and fascia with a damp cloth; water and a little washing up liquid are adequate. Do not use sponges with a rough surface or abrasive detergents, as these could scratch the surfaces. Stainless steel appliances: To prevent corrosion, avoid using sponge cloths or wash them out thoroughly several times before using for the first time. a=Warning Never use other chlorinated household detergents! Health hazard! Special salt and rinse aid – Check the refill indicators ` and X. If required, refill salt and/or rinse aid. en Filters The filters 1R keep large foreign objects in the rinsing water away from the pump. These foreign objects may occasionally block the filters. The filter system consists of a coarse filter, a flat fine filter and a microfilter. – After each washing cycle check the filters for residue. – Unscrew filter cylinder as illustrated and take out filter system. –Remove any residue and clean filters under running water. –Re-install filter system in reverse sequence and ensure that the arrow marks are opposite each other after closing the filter system. Spray arms Limescale and contaminants in the rinsing water may block nozzles and bearings on the spray arms 1: and 1B. – Check outlet nozzles on the spray arms for blockages. – Unscrew the upper spray arms 1: (1/ 4 revolution). – Remove the lower spray arm 1Bupwards. – Clean spray arms under running water. –Re-engage or screw on spray arms. en Troubleshooting The majority of faults which could occur in daily operation can be rectified by the user. This ensures that the appliance is quickly available for use again. The following overview will help you locating the causes and gives helpful advise to eliminate them. Note If the appliance stops during dishwashing or does not start for no obvious reason, first run the Abort programme function (Reset). (See chapter entitled “Dishwashing”) a=Warning Don’t forget: Repairs may be carried out by technicians only. If a component has to be replaced, ensure that only original spare parts are used. Improper repairs or use of non-original spare parts may cause considerable damage and put the user at considerable risk. Waste water pump Large food remnants or foreign objects which were not captured by the filters may block the waste water pump. The rinsing water will then be above the filter. In this case: – First always disconnect the appliance from the power supply. – Take out top basket 1" and bottom basket 1b. – Remove the filters 1R. – Scoop out water, use a sponge if required. – Prise out the white pump cover (as illustrated) using a spoon. Grip the cover on the crosspiece and lift diagonally inwards. Remove cover completely. – Check impeller wheel and remove any foreign objects. – Place cover in the original position and press down until it engages (click). – Install filters. – Re-insert baskets. en ... when the appliance is switched on The appliance does not start. – The mains fuse has tripped. – The appliance plug has not been inserted. – The appliance door has not been shut properly. ... on the appliance Lower spray arm rotates sluggishly. – Spray arm blocked. The door is difficult to open. * – Child-proof lock is activated. The deactivation instructions are at the back in the envelope. * depending on model Door cannot be closed. – Door lock has been activated. To reset, close the door with greater force. Cover on the detergent dispenser cannot be closed. – Detergent dispenser overfilled or mechanism blocked by sticky detergent residue. Detergent residue in the detergent dispenser. – Dispenser was damp when filled. “Check water supply” display h lights up. – Tap turned off. – Water supply interrupted. – Supply hose kinked. – Filter in the water supply blocked. – Switch off the appliance and pull out the mains plug. – Turn off the tap. – Clean filter in the supply hose. – Reconnect power supply. – Turn on the tap. – Switch on the appliance. – Water is left in the appliance at the end of the programme. – Waste water hose is blocked or kinked. – Waste water pump blocked, cover on the waste water pump is not locked in position (see Waste water pump). – Filters blocked. – The programme has not yet ended. Wait until programme ends or implement “Reset” function. The “Check water supply” display h flashes rapidly. – Water in the safety system. – Switch off the appliance and pull out the mains plug. – Turn off the tap. – Call customer service. Refill indicator for salt ` and/or rinse- aid X is not lit. – Refill indicator/s switched off. – Adequate salt/rinse-aid available. Refill indicator for special salt ` is lit...
Questo manuale è adatto anche per i modelli :Lavastoviglie - DRS4302/06 (1.27 mb)
Lavastoviglie - DRS4302/07 (1.27 mb)
Lavastoviglie - DRS4302/09 (1.27 mb)
Lavastoviglie - DRS4308/01 (1.27 mb)