valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
Switch off the main switch 1 . The setting is stored. Switching the dishwasher OFF Several minutes after the programme has ended: Open the door when the programme has ended. Set main switch 1 to OFF. Turn the water tap off. (Does not apply when Aqua-Stop unit has been fitted) Remove dishes, etc. when they have cooled down. en Programme interruption Carefully open the door, it could happen that water splashes out of the appliance. Only open completely when the spray arm no longer turns. If the programme is already in “drying” mode, an acoustic signal reminds you to close the appliance door or to abort the programme. Switch OFF the main switch 1 . Indicator light goes out. The programme remains stored. If warm water is connected or if the machine is already heated up and the appliance door has been opened, leave the door slightly ajar, then close it, otherwise the appliance door can jump open through the expansion. In order to continue the programme flow, switch the main switch ON again and close the door. Cancel programme (Reset) Only when the master switch is ON. Press the A and C programme buttons simultaneously and hold them pressed for approx. 3 sec. The programme continues for approx. 1 min. The PROGRAMME END indicator and the indicator for the programme that has just been terminated light up. Set main switch 1 to OFF. Close the detergent compartment 30 . To restart the dishwasher, set main switch to ON again and select desired programme. Changing the programme It is possible to change the programme selection after you have switched the dishwasher on, provided that you have not yet closed the door. If it is necessary to change the programme after this, the programme cycle that has already begun (e.g. washing) will still carry on to the end. Maintenance and care A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems. Therefore you should occasionally have a careful look inside your dishwasher. Overall condition of the machine Check spray arm for grease and limescale deposits. If you find such deposits: Fill the detergent dispenser with detergent, start the appliance without utensils in the programme which has the highest wash temperature. Clean the appliance with detergents/ appliance cleaners which are particularly suitable for use with dishwashers. Regularly wipe the door seal with a damp cloth to remove deposits. Never use a steam cleaner to clean your dishwasher. The manufacturer is not liable for any consequential damage. Attention! Never use other chlorinated household detergents! Health hazard! Dishwasher salt Check the LOW SALT indicator 5 or 24 . Top up with salt, if required. Rinse-aid Check the LOW RINSE-AID indicator 6 on the front panel or the level indicator on the rinse-aid container 29 . Top up with rinse-aid, if required. en Filters The filters 25 prevent larger remnants of food or other objects from getting inside the pump. This residue can occasionally clog up the filters. The filter system consists of a filter cylinder, a flat fine filter and, depending on the model, a microfilter (*). Inspect the filters for obstructions every time the dishwasher has been used. By unscrewing the filter cylinder, you can remove the filter system. Remove any food remnants and clean the filters under running water. Reassembly: Insert the filter system and screw down with the filter cylinder. en 21 Spray arms Lime and remnants of food in the washing water can block the nozzles in the spray arms 22 and 23 and the arm mountings . Inspect the nozzles in the spray arms for blocked holes due to remnants of food. If necessary, pull the lower arm 23 upwards and lift it off. Unscrew the upper spray arm 22 . Clean both spray arms under running water. 0 1 2 3 Refit the spray arms. Ensure that the lower arm has locked into place and the upper one is screwed tight. Pump * * on applicable models Larger remnants of food that have not been trapped by the filters and have been left in the water can cause a blockage in the pump. The water is no longer pumped out of the dishwasher and it can be seen covering the filter. Proceed as follows: Ladle out as much water as possible. Remove the filters 25 . Undo the screw in the cover (Torx T 20) and remove the cover. Inspect the inside and remove any obstructions that you find. Re-insert the cover and screw down. Re-insert the filters and screw down. Torx T20 2 1 en Fault finding Resolving minor problems yourself Experience has shown that you can resolve most problems that arise during normal daily usage yourself, without having to call out a service engineer. Not only does this save costs, but it also means that the appliance is available for use again that much sooner. The following list of common occurrences and their remedies should help you identify the causes of most problems. Problems ... Attention Remember: Repairs may be carried out by a technician only. If a component has to be replaced, ensure that only...
Questo manuale è adatto anche per i modelli :Lavastoviglie - SE6TIE2GB/70 (1.85 mb)
Lavastoviglie - SE6TIE2GB/72 (1.85 mb)
Lavastoviglie - SE6TIE2GB/73 (1.85 mb)
Lavastoviglie - SE6TIE2GB/74 (1.85 mb)