valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
en Additional options * depending on model Additional options can be set with the buttons 8. Y Express Wash/ Speed Perfect * The >>Express Wash/ Speed Perfect<< function can reduce the running time by approx. 20% to 50% depending on the selected rinse programme. To obtain optimum cleaning and drying results at a reduced running time, water and energy consumption are increased. § Half load * If you have only a few items to wash (e.g. glasses, cups, plates), you can switch to “half load”. This will save water, energy and time. It is recommended to put a little less detergent in the detergent dispenser than for a full load. Washing the dishes Programme data The programme data (consumption values) can be found in the summary of instructions. This data refers to normal conditions and the water hardness set value 2. Different influencing factors such as water temperature or mains pressure may result in deviations. Switching on the appliance – Turn on the tap fully. – Open the door. – Switch on the main switch (. The display of the last selected programme lights up. This programme runs if no other programme button ` is pressed. – Close the door. The programme starts running. End of programme The programme has ended when the programme end display @ and the display of the executed programme are lit. The end of the programme is also indicated by an acoustic signal. This function can be changed as follows: – Open the door. – Hold down programme button 3 and switch on the main switch (. – Release both buttons. The programme button 3 flashes. To change the setting: – Press programme button 3. Each time the Programme button 3 is pressed, the buzzing sound changes in 4 stages (from off to loud). – Switch off main switch (, the set value is saved. – Close the door. en Switching off the appliance Short time after the end of the programme: – Open the door. – Switch off the main switch (. – Turn off the tap (not applicable if Aqua- Stop fitted). – Remove the utensils when they have cooled down. a=Warning At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops. Interrupting the programme – Open the door. – Switch off the main switch (. The LEDs go out. The programme is saved. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. – To continue the programme, switch on the main switch ( again. – Close the door. Terminating the programme (Reset) – Open the door. – Simultaneously press programme buttons # and 3 for approx. 3 sec. – Close the door. The programme sequence lasts approx. 1 min. – Programme end display @ is lit. – Open the door. – Switch off the main switch (. – Close the door. Changing the programme After you have switched the appliance on, it is possible to change the programme within 2 min. If you want to change the programme afterwards, the appliance waits until the initiated programme section (e. g. washing) ends. en Maintenance and care A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems. Overall condition of the machine – Check spray arm for grease and limescale deposits. If you find such deposits: – Fill detergent dispenser with detergent. Start the appliance without utensils in the programme with the highest rinsing temperature. Clean the appliance with detergents/ appliance cleaners which are particularly suitable for use with dishwashers. – Regularly clean door seal with a damp cloth. Never use a steam cleaner to clean your dishwasher. The manufacturer is not liable for any consequential damage. Regularly wipe the front of the appliance and fascia with a damp cloth; water and a little washing up liquid are adequate. Do not use sponges with a rough surface or abrasive detergents, as these could scratch the surfaces. Stainless steel appliances: To prevent corrosion, avoid using sponge cloths or wash them out thoroughly several times before using for the first time. a=Warning Never use other chlorinated household detergents! Health hazard! Special salt and rinse aid – Check the refill indicators P and X. If required, refill salt and/or rinse aid. Filters The filters 1J keep large foreign objects in the rinsing water away from the pump. These foreign objects may occasionally block the filters. – After each wash cycle check the filters for residue and clean if required. – After unscrewing the coarse microfilter, you can take out the filter group. – Remove any residue and clean filters under running water. – Re-install filter system in reverse sequence and ensure that the arrow marks are opposite each other after closing the filter system. en Spray arms Limescale and contaminants in the rinsing water may block nozzles and bearings on ...
Questo manuale è adatto anche per i modelli :Lavastoviglie - SF6VZE3CH/40 (1.38 mb)
Lavastoviglie - SF6VZE3CH/41 (1.38 mb)
Lavastoviglie - SF6VZE3CH/42 (1.38 mb)
Lavastoviglie - SF6VZE3CH/44 (1.38 mb)