valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
Only customer service may maintain, remove and install the float. en Water hardness table Water softening system To ensure good washing results, the dishwasher requires soft water, i.e. containing low amounts of lime, otherwise white limescale will be deposited on the utensils and inner container. Tap water above 9° Clarke must be softened. The water is softened with salt (regeneration salt) in the water softening system of the dishwasher. The setting and therefore the required amount of salt depends on the degree of hardness of your tap water (see table). Setting The amount of salt dispensed can be set from ‹ to .. Sal is not required at the set value ‹. – Find out about the hardness value of your tap water. Your water utility company will help you with this. – Set value can be found in the water hardness table. – Close the door. – Hold down programme button + and switch on the main switch (. – Release both buttons. The LED for button + flashes and the digital display 8 displays the factory setting …. To change the setting: – Press programme button +. Each time the button is pressed, the set value increases by one level; when the value of . has been reached, the display jumps back to ‹ (off). – Switch off the main switch ( The chosen setting has now been stored. . & . . # $ . . '. $% . . . !!!"!!!!!!!!!!"!! . . . . . . . . en Special salt $ Using special salt Always refill with special salt immediately before switching on the appliance. This ensures that overrun special salt solution is immediately washed out and does not corrode the rinsing tank. – Open the screw-type cap of the compartment 1Z. – Fill the tank with water (only required when switching on the appliance for the first time). – Then add salt (not table salt). The water is displaced and runs out. * depending on model The salt refill indicator P on the fascia is lit. It goes out as soon as a sufficiently high salt solution has formed. If the set value ‹ is displayed, do not add any salt because salt will not be used during operation of the appliance, the salt display is switched off. If the set values ‚ to . are displayed, salt must be added. Using detergents with salt component If combined detergents with a salt component are used, salt can usually be omitted up to a water hardness of 21° dH (37° fH, 26° Clarke, 3.7 mmol/l). If the water hardness is over 21° dH, special salt must be used. Salt refill indicator As soon as the salt refill indicator P on the fascia is lit, top up the salt. Depending on the washing frequency and the hardness setting, the regeneration salt may not have to be topped up for several months. If the salt refill indicator P is impaired (e. g. when using combined detergents containing salt component), it can be switched off. – Proceed as described under “Setting water softening system” and set the value to ‹. The water softening system and salt refill indicator are now switched off. a=Caution Never fill the salt dispenser with detergent. You will destroy the water softening system. en Rinse aid % As soon as the rinse-aid refill indicator X is lit on the fascia, there is still a rinse-aid reserve of 1–2 rinsing processes. Refill with rinse aid. The rinse aid is required for stain-free utensils and clear glasses. Use only rinse aid for domestic dishwashers. Combined detergents with rinse-aid component may be used up to a water hardness of 21° dH (37° fH, 26° Clarke, 3.7 mmol/l) only. If the water hardness is over 21° dH, rinse aid must be used. – Open the cover on the rinse-aid dispenser 9". To do this, press the mark (1) on the cover and simultaneously lift the cover on the control plate (2). – Carefully pour in the rinse aid to just below the edge of the filler opening. –Close cover until it clicks shut. –To prevent excessive foam formation during the next rinse cycle, remove any rinse aid which has run over with a cloth. Setting amount of rinse aid The rinse aid dispensing rate can be adjusted steplessly. The clear rinse controller was set to 4 at the factory. Do not change the position of the rinse aid control unless there are streaks (rotate towards –) or water stains (rotate towards +) on the utensils. . . Switching the rinse aid refill indicator off or on If the rinse-aid refill indicator X is impaired (e.g. when using combined detergents containing rinse aid component), it can be switched off. To change the setting: – Close the door. – Hold down programme button 3 and press main switch ( until the digital display 8 illuminates. – Release buttons. On the digital display 8 ‚ is indicated (rinse-aid refill indicator on). – By pressing button 3 you can switch the rinse-aid indicator off ‹ or on ‚. – Switch off the main switch (; the chosen setting has now been stored. en Utensils Not suitable – Cutlery and utensils made of wood. – Delicate decorative glasses, craft and antique utensils. These decors are not dishwasher-proof. – Plastic parts not resistant to heat. – Copper and tin utensils. – Utensils...
Questo manuale è adatto anche per i modelli :Lavastoviglie - SGS45N62EU/39 (2.34 mb)
Lavastoviglie - SGS45N68EU/36 (2.34 mb)
Lavastoviglie - SGS45N68EU/39 (2.34 mb)