valutazioni - 0, GPA: 0
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
4 litres of water are required for regenerating the water softening system. The overall water consumption per load can therefore be increased by between 0 and a maximum of 4 litres according to the water hardness setting. en Filling in the Salt Function of the salt During the rinse cycle the salt is being washed automatically from the salt compartment into the softening system where it will dissolve the lime. The lime-containing solution drains from the dishwasher. Afterwards the softening system is ready to be loaded again. This regeneration cycle will only work if the salt is dissolved in water. Open the screw-type cap of the compartment 27 . Before switching on the appliance for the first time, pour approx. 1 litre of water into the salt dispenser. Then refill with salt (not cooking salt) until the salt container is full (max. 1.5 kg). When you refill the salt, water is being displaced and drains off. Therefore, to prevent corrosion, always refill with salt immediately before switching on the dishwasher. This way the overflowing salt solution is diluted and flushed immediately. Use the enclosed salt filling aid ( in some models). Then clean the filling area of salt residues and screw the compartment lid back on without tilting the lid. The LOW SALT indicator 6 on the front panel will light up initially but will extinguish again after a short period when the salt solution has become sufficiently concentrated. If the set hardness value is , do not add salt because no salt is used during operation; the salt refill indicator is switched off. Do not pour detergent into the container for special salt. This would destroy the water softener. Salt refill indicator As soon as the salt refill indicator 6 is lit on the control panel, refill with salt immediately before the next rinse cycle. Depending on the washing frequency and the hardness setting, the regeneration salt may not have to be topped up for several months. en Adding rinse aid The rinse aid is required for stain-free utensils and clear glasses. Use only rinse aid for domestic dishwashers. Open the cover on the rinse-aid dispenser 30 . To do this, press the mark (1 ) on the cover and simultaneously lift the cover on the control plate (2 ). Adjusting the amount of rinse-aid The amount of rinse-aid added to the water can be varied by adjusting the stepless control. The rinse-aid control has been set to ”4” in the factory. Do not alter the setting of the rinse-aid control unless streaks (turn knob towards ”–”) or water marks (turn knob towards ”+”) are left on the dishes. 30 Carefully pour in the rinse aid to just below the edge of the filler opening. Close the lid, ensuring that you hear it snap closed. To prevent excessive foam formation during the next rinse cycle, remove any rinse aid which has run over with a cloth. Rinse aid controller Rinse-aid refill indicator As soon as the rinse-aid refill indicator lights up on the control panel 7 , refill with rinse aid. If using detergent products with integrated rinse aid, the rinse-aid refill indicator can be switched off (see “Switching the rinse-aid refill indicator off and on” in the “auto 3in1” chapter). en Not suitable for the dishwasher The following should not be cleaned in the dishwasher: Wooden cutlery and utensils – these will leach out and become unsightly; even the utilised stickers are not suitable for the temperatures which occur. Sensitive ornamental glasses, craft utensil and vases, special antique or irretrievable utensils. These ornaments are not dishwasher-proof. Plastic parts sensitive to hot water. Copper and tin utensils. Utensils which are soiled with ash, wax, lubricating grease or ink. Absorbent materials such as sponges and cloths. Aluminium and silver parts have a tendency to discolour and fade during the wash cycle. Even some types of glass (e.g. crystal glass objects) may turn cloudy after many wash cycles. Recommendation: In future buy utensils which are identified as dishwasher-proof. Damage to glassware and other dishes Possible causes: type of glass or manufacturing process chemical composition of detergent water temperature and duration of dishwasher programme. Suggested remedy: Use glassware or porcelain dishes that have been marked ’dishwasher–proof’ by the manufacturer. Use a mild detergent that is described as ’kind to dishes’. If necessary, seek further information from detergent manufacturers. Select a programme with as low a temperature and as short a duration as possible. To prevent damage, take glass and cutlery out of the dishwasher as soon as possible after the programme has ended. en Arranging crockery, glasses, etc. in the dishwasher Loading the dishwasher Remove fairly large food remnants, e.g. pieces of bone and fruit stones, from the utensil. It is not necessary to rinse the dishes under running water. Place objects in the dishwasher in such a way that items such as cups, glasses, pots/pans, etc. are stood upside down, curved items, or those with recesses, sho...
Questo manuale è adatto anche per i modelli :Lavastoviglie - SGS46E12EU/02 (2.45 mb)
Lavastoviglie - SGS46E12EU/04 (2.45 mb)
Lavastoviglie - SGS46E12EU/05 (2.45 mb)
Lavastoviglie - SGS46E12EU/09 (2.45 mb)