Extra drying Clean 50° -60° Final rinse 55° -65° all types of utensils cold rinsing, intermediate cleaning u / o Prerinse none Prerinse Programme selection You can select a suitable programme according to the type of utensils and degree of soiling. Information for test institutes Test institutes receive the information for comparability tests (e.g. according to EN60436). These are the conditions for conducting the tests, however these are not the results or consumption values. Request by e-mail to: dishwasher@test-appliances.com The product number (E no.) and the production number (FD) are required which you can find on the rating plate 9: on the appliance door. TurboSpeed 20 min. – especially quick rinsing programme with one-off preheating* * depending on model The appliance is heated up once (approx. 25 min.), then the appliance is loaded and several quick rinse cycles (20 min. each) can run in succession. Note Detergent tablets are not suitable for this programme, as the detergent cannot completely dissolve within the short time. Therefore always use powder detergents and ensure that the salt and rinse aid dispensers are always filled and set to the correct value (see chapters entitled “Salt” and “Rinse aid”). Overview of programmes en Please read the operation carefully, the programme differs from the other programmes. 1. Open the door. 2. Switch on ON/OFF switch (. 3. Select programme TurboSpeed 20 min. • flashes on the digital display h (• = Heating phase). 4. Press START button `. 5. Close the door. The heating up phase of the empty appliance starts. The light spot on the floor is lit constantly. If the appliance is loaded before the heating phase, the duration of the heating phase is extended. 6. As soon as the light spot on the floor flashes, open the appliance. p flashes on the digital display h (p = Load). Attention! Interior is hot. 7. Load the appliance and start the rinsing phase by pressing the START button `. 8. When the rinse cycle has ended, the light spot on the floor flashes again and the buzzer is activated. 9. Open the door. ‹:‹‹ is indicated on the digital display h, remove the utensils. Shortly afterwards p flashes again on the digital display h. Attention! The utensils are hot and sensitive to shock! 10. If more rinse cycles are required, reload dishwasher, press the START button ` and close the door. 11. If no more rinse cycles are required, switch off ON/OFF switch ( and close the door. en Additional options 0 Additional options * depending on model Additional options can be set with the buttons X. A Save time (VarioSpeed+) * The >>Save time<< function can reduce the running time by approx. 20% to 66% depending on the selected rinse programme. To obtain optimum cleaning and drying results at a reduced running time, water and energy consumption are increased. § Half load * If you have only a few items to wash (e.g. glasses, cups, plates), you can switch to “half load”. This will save water, energy and time. It is recommended to put a little less detergent in the detergent dispenser than for a full load. .HygienePlus * This function increases the temperatures and retains them for an extra long time to obtain a defined disinfection performance. This increases the hygiene status. This additional option is ideal for cleaning e.g. chopping boards and baby bottles. I Intensive zone * Perfect for a mixed load. You can wash very soiled pots and pans in the lower basket together with normally soiled utensils in the upper basket. The spray pressure in the lower basket is intensified, the rinsing temperature is increased slightly. . Extra drying * An increased temperature during the final rinse and an extended drying phase ensure that even plastic parts dry better. There is a slight increase in the energy consumption. 1 Operating the appliance Programme data The programme data (consumption values) can be found in the summary of instructions. They refer to normal conditions and the water hardness set value •:‹…. Different influencing factors such as e.g. water temperature or line pressure may result in deviations. Operating the appliance en Aqua sensor * * depending on model The Aqua sensor is an optical measuring device (light barrier) which measures the turbidity of the rinsing water. The Aqua sensor is used according to the programme. If the Aqua sensor is active, “clean” rinsing water can be transferred to the next rinse bath and water consumption can be reduced by 3–6 litres. If the turbidity is greater, the water is drained and is replaced with fresh water. In the automatic programmes the temperature and running time can also be adjusted to the degree of soiling. Switching on the appliance 1. Turn on the tap fully. 2. Open the door. 3. Switch on ON/OFF switch (. The Eco 50° programme display flashes. This programme remains selected if no other programme button 0 is pressed. The expected programme duration flashes on the digital display h. 4. Press the START button `. 5. Close the door. T...

Questo manuale è adatto anche per i modelli :
Lavastoviglie - SPV53M40EU/14 (1.61 mb)