Produttore : Bosch File Size : 1.88 mb File Nome : Lingua di insegnamento:

Vai a scaricare

It is recommended to have a water temperature (temperature of the incoming water) of at least 40 °C and no more than 60 °C. It is not recommended to connect the appliance to hot water if the water is supplied from an electric boiler. Setting hot water: 1. Close the door. 2. Switch on ON/OFF switch (. 3. Hold down programme button # and press START button P until •:‹... is indicated on the digital display. 4. Release both buttons. The LED for button # flashes and the digital display )" displays the factory setting •:‹…. 5. Press programme button # until the factory set value ‘:‹‹ is indicated on the digital display )". To change the setting: 1. By pressing the 3 button, you can switch the hot water setting off ‘:‹‹ or on ‘:‹‚. 2. Press START button P. The set value is saved. Electrical connection . Connect the appliance to an alternating current only, ranging from 220 V to 240 V and 50 Hz or 60 Hz via a correctly installed socket with protective earth conductor. See rating plate for required fusing 92. . The socket must be near the appliance and freely accessible following installation. If the plug is not freely accessible, an allpole disconnector with a contact opening of at least 3 mm must be fitted on the installation side to satisfy the relevant safety instructions. Installation and connection en . The connection may be modified by technicians only. . A power cord extension may be purchased from customer service only. . Use only a residual current operated circuit-breaker which features the symbol ‚. Only this extension guarantees compliance with the currently valid regulations. . The appliance features a water damage protection system. Please note the system will not function unless the power supply is connected. Removing the appliance Also observe the sequence of worksteps here. 1. Disconnect the appliance from the power supply. 2. Turn off the water supply. 3. Disconnect the waste water and fresh water connections. 4. Loosen fastening screws for the furniture parts. 5. If fitted, remove the base panel. 6. Pull out the appliance, carefully pulling the hose behind. en Installation and connection Transportation Empty the dishwasher and secure loose parts. Drain the appliance according to the following steps: 1. Turn on the tap. 2. Close the door. 3. Switch on ON/OFF switch (. 4. Select programme with the highest temperature. The expected programme duration is indicated on the numerical display )". 5. Press START button P. Programme sequence starts. 6. After approx. 4 minutes press the START button P until ‹:‹‚ is indicated on the digital display. After approx. 1 min ‹:‹‹ is indicated on the digital display . 7. Switch off ON/OFF switch (. 8. Turn off the tap, disconnect supply hose and drain water. Transport appliance upright only. (This prevents residual water from running into the machine control and damaging the programme sequence.) Protection against frost If the appliance is in a room where there is a risk of frost (e.g. holiday home), empty the appliance completely (see Transportation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en 7&". (9211) 640MA ...

Questo manuale è adatto anche per i modelli :
Lavastoviglie - S41M53N4EU/32 (1.88 mb)
Lavastoviglie - S41M53N4EU/36 (1.88 mb)
Lavastoviglie - S41M53N4EU/43 (1.88 mb)
Lavastoviglie - S41M53N4EU/51 (1.88 mb)

Scarica la tua

Per scaricare, digitare 2 cifre :