valutazioni - 0, GPA: 0
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
They refer to normal conditions and the water hardness set value •:‹…. Different influencing factors such as e.g. water temperature or line pressure may result in deviations. Aqua sensor * * depending on model The Aqua sensor is an optical measuring device (light barrier) which measures the turbidity of the rinsing water. The Aqua sensor is used according to the programme. If the Aqua sensor is active, “clean” rinsing water can be transferred to the next rinse bath and water consumption can be reduced by 3–6 litres. If the turbidity is greater, the water is drained and is replaced with fresh water. In the automatic programmes the temperature and running time can also be adjusted to the degree of soiling. Operating the appliance en Switching on the appliance 1. Turn on the tap fully. 2. Open the door. 3. Switch on ON/OFF switch (. The Eco 50° programme display flashes. This programme remains selected if no other programme button 0 is pressed. The expected programme duration flashes on the digital display h. 4. Press the START button `. 5. Close the door. The programme starts running. Note -for environmentally friendly operation of the dishwasher: For ecological reasons the Eco 50° programme is preset whenever the appliance starts. This conserves environmental resources and not least saves you money. The Eco 50° programme is a particularly environmentally friendly programme. According to EU regulation 1016/2010 it is the “Standard programme” which is the most efficient standard cleaning cycle for cleaning normally soiled utensils in terms of the combined energy and water consumption for cleaning these types of utensils. Programme TurboSpeed 20 min.: When the START button ` is pressed the first time, the heating up phase (approx. 25 min., irrespective of the initial situation) of the appliance starts. When the appliance has been opened and loaded and the START button ` pressed, the rinsing phase (20 min.) starts when the door is closed. en Operating the appliance Optical display while the programme is running * * depending on model While the programme is running, an optical display is indicated on the floor under the appliance door. If the base panel is pulled forwards or if the appliance is installed at eye- level with flush furniture front, the display is not visible. Possible settings of the optical display: †:‹‹ The display is switched off. †:‹‚ Programme, timer programming, remaining time, end of programme and, if required, low water level are displayed. †:‹. Same as †:‹‚. Other programme information is also displayed, e.g. the symbol for half load § or glass protection system active W. †:‹‚ is set at the factory. To change the setting: 1. Open the door. 2. Switch on ON/OFF switch (. 3. Hold down programme button # and press START button ` until •:‹.... is indicated on the digital display. 4. Release both buttons. The illuminated display of the button # flashes. 5. Keep pressing programme button # until the previously set value, e.g. †:‹‚, is indicated on the digital display h †:‹... (for the optical display). 6. Keep pressing programme button 3 until the required value, e.g. †:‹., is indicated on the digital display h. 7. Press START button `. The set value is saved. 8. Close the door. The following applies to TurboSpeed 20 min.: During the heating up phase the light spot * or • *(• = Heating phase) is lit on the floor. At the end of the heating up phase the light spot * or p *(p = Load) flashes, indicating that the appliance can be opened and loaded. Operating the appliance en Remaining running time display When the programme is selected, the programme running time is indicated on the digital display h. When the programme has started, the remaining running time is displayed on the floor (only for settings †:‹‚ and †:‹.). The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme). Timer programming * * depending on model You can delay the start of the programme in 1-hour steps up to 24 hours. 1. Open the door. 2. Switch on ON/OFF switch (. 3. Press button P + until the digital display h jumps to oe:‹‚. 4. Press P + or – button until the displayed time corresponds with your requirements. 5. Press START button `, timer programming is activated. 6. To delete timer programming, press the P + or – button until h oe:‹‹ is indicated on the digital display. You can change your programme selection at any time until the programme starts. 7. Close the door. End of programme The end of the programme O (End) is displayed on the floor – provided the optical display is switched on and is visible. The end of the programme is also indicated by an acoustic signal. This function can be changed as follows: 1. Open the door. 2. Switch on ON/OFF switch (. 3. Hold down programme button # and press START button ` until •:‹.... is indicated on the digital display. 4. Release both buttons. The LED for butt...
Questo manuale è adatto anche per i modelli :Lavastoviglie - S51N69X5EU/73 (2.09 mb)
Lavastoviglie - S52N69X5EU/50 (2.09 mb)
Lavastoviglie - S52N69X5EU/73 (2.09 mb)