valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
Rust spots in washer use. the washing compartment Rust spots are visible in are from particles from out- the washing compartside the appliance (rust parment. ticles from the water pipe, from pans, cutlery, etc.). Remove such spots with a Close the lid of the special salt container securely. commercially available stainless steel cleaner. There is a whistling The whistling is not a cause Use a different brand of noise during washing. for concern. detergent. ...the wash result is unsatisfactory. The dishes are still dirty. – The wrong wash programme was selected. – The dishes were arranged in such a manner that water has not reached all parts. The dish racks must not be overloaded. – The filter in the base of the washing compartment is dirty or incorrectly positioned. – Detergent was not used or too little was used. Operating Instructions – In the case of scale deposits on the dishes: the special salt container is empty or the water softener is incorrectly adjusted. – The drain hose is incorrectly laid. The dishes are wet and dull. – Rinse aid was not used. – The rinse aid container is empty. There are streaks, milky spots or a bluish coating on glasses and dishes. – Decrease rinse aid dosing. There are dried water drops on the glasses and dishes. – Increase rinse aid dosing. – The detergent may be the cause. Contact the detergent manufacturer's consumer advisor. Operating Instructions Technical Data Capacity: 12 place settings including serving dishes Permitted Water 1-10 bar (=10-100 N/cm2 = 0.1-1.0 MPa) Pressure: Information on the electrical connection is given on the Electrical Connection: rating plate on the inner edge of the dishwasher door on the right. Dishwasher: Free-Standing Appliances Dimensions: 850 x 600 x 600 (H x W x D in mm) Max. Weight: 54 Kg Dishwashers that Can Be Integrated, Built-In Dishwashers Dimensions: 820 – 880 x 596 x 570 (H x W x D in mm) Max. Weight: 50 Kg Dishwashers that Can Be Fully Integrated Dimensions: 820 – 880 x 596 x 546 - 550 (H x W x D in mm) Max. Weight: 50 Kg ; This appliance conforms with the following EU Directives: – 73/23/EWG dated 19. 02. 1973 – Low Voltage Directive – 89/336/EWG dated 03. 05. 1989 (including Directive Amendment 92/31/EWG) – EMC Directive Operating Instructions 28 Notes for Test Institutes Testing in accordance with EN 60704 must be carried out with the appliance fully loaded and using the test programme (see Programme Table). Tests in accordance with EN 50242 must be carried out when the salt dispenser and rinse aid container have been filled with salt and rinse aid respectively and using the test programme (see Programme Table). Sample loading arrangements: Upper basket Lower basket with cutlery basket Cutlery basket Full Load: 12 place settings incl. serving dishes Half Load: 6 place settings incl. serving, leaving alternate positions free Detergent Dosing: 5g + 25g (Type B) 20g (Type B) Rinse Aid Setting: 4 (Type III) 4 (Type III) Installation and Connection Instructions INSTALLATION AND CONNECTION INSTRUCTIONS Installing the Dishwasher • The dishwasher must be installed on a firm floor and adjusted such that it is stable and level. • To compensate for unevenness in the floor and to match the height of the appliance to that of surrounding units extend the threaded feet by unscrewing: – use a screwdriver. • The drain hose, inlet hose and mains cable must be laid such that they are free to move in the rear of the plinth recess, so that they cannot be kinked or crushed. Free-Standing Appliances 1 • can be set up as stand-alone without additional installation. If the dishwasher is set up next to a gas or coal cooker, a heat- insulating, non-flammable plate must be mounted between the dishwasher and the cooker, flush to the top edge of the work surface (depth 57.5 cm). The plate should have aluminium foil on the side facing the cooker. Installation and Connection Instructions • If the dishwasher is installed underneath a kitchen work surface, the original work surface of the dishwasher is to be removed as follows: – Unscrew the screws (1) from the elbows on the back side. – Slide the work surface approx. 1cm to the rear (3) , lift at the front (4) and remove. – Press the work surface retaining brackets at the position shown in the diagram (4) and remove the bracket at an angle to the rear (5). • The dishwasher must also be screwed on tightly to the work surface or to the adjoining units. This is absolutely necessary so that its stability is guaranteed according to VDE regulations. 1 If the dishwasher is later used as a free-standing appliance, the original work surface must be re-mounted. 3 The plinth on free-standing appliances is not adjustable. Installation and Connection Instructions Connecting the Dishwasher Water Connection The dishwasher is fitted with safety devices that prevent the wash water returning into the drinking water system and comply with the applicable plumbing regulations. • The dishwasher can be connected to cold and hot w...