valutazioni - 3, GPA: 3.7
(
)
)
|
Facilità d'uso
1 It is only possible to adjust the water hardness setting when a programme is not running. If you have inadvertently started a programme (an LED indicator is constantly illu be cancelled by pressing the 0 1. The dishwasher must be switched off. 2. Manual setting: Open the door on the dishwashe 3. Remove the lower basket dishwasher. 4. Turn the water hardness switch or 1. 5. Re-position the lower basket. 6. Electronic setting: Press the water-softener and f tion buttons simultaneously and ke them pressed. 7. In addition press the ON/OFF button. 8. The LED indicator for the water-softener button flashes. 9. Press the water-softener button again. – The LED indicator for the water-softener button will be illuminated continuously for an initial 5 seconds and then begin to flash. – The number of flashes corresponds to the hardness setting. – The sequence of flashes is repeated several times after a 5 second pause. 10. Each time you press the water-softener button the hardness setting will go up by 1. (Exception: Hardness setting 1 follows hardness setting 5). – If the hardness setting is changed, the LED indicator for the water- softener button will confirm the change by remaining illuminated continuously for 5 seconds and then flashing again. – The number of flashes corresponds to the new hardness setting. – The sequence of flashes is repeated several times after a 5 second pause. 11. Once the hardness setting is correct, press the ON/OFF button. The hardness setting is then saved. 11 Operating Instructions Filling with Salt for the Water Softener 1 Use only salt designed for dishwashers. Never fill the salt container with any another type of salt (e.g. culinary salt) or dishwasher detergent as this would irreparably damage the water softener. Prior to filling with salt, please check each time that you really do have a packet of dishwasher salt in your hand. Fill with dishwasher salt: – Prior to using the dishwasher for the first time – When the SALT indicator J on the control panel is illuminated. 3 If the water hardness in your area is less than 4 °d, you do not need to use dishwasher salt. The SALT indicator J3 The water expelled by filling the salt container with salt runs o salt container onto the base of the washing compartment. This is cause for concern, the water will be pumped out at the start of the SALESALTSALZSEL remain illuminated. 0 1. Open the door, remove the lower basket. 2. Undo the lid on the salt container by turning it anticlockwise. 3. When using for the first time: fill the salt container with water. 4. Place the funnel supplied on the container opening. Fill the container with salt through the funnel; the capacity of the co tainer is approx. 1.0-1.5 kg depending on the grain size. Do not overfill the salt container with salt. next wash programme. 5. Clean any salt remnants on the container opening. 6. Turn the lid clockwise to the stop, otherwise dishwasher salt will leak into the wash water, this could lead to poor wash results. To avoid this run a rinse programme after filling the salt container with special salt. This will wash away salt water and any salt crystals that have been spilt. 3 Depending on the size of the salt grains, it can take several hours for the salt to dissolve in the water and the special salt indicator J to extinguish. The setting of the water softener and the consumption of salt are dependent on the hardness of the local water. Operating Instructions Filling with Rinse Aid Rinse aid is automatically added during the last rinse, ensuring thor ough rinsing, spot and streak free drying. 1 Only use rinse aid specifically designed for domestic dishwashers. Never fill the rinse aid container with any other substance as this would damage the appliance. Fill with rinse aid: – Prior to using the dishwasher for the first time – When the window indicator has a dark centre surrounded by a light ring. If there is rinse aid in the container, the indicator window is completely dark. The rinse aid compartment is on the inside of the dishwasher door. 0 1. Open the door. 2. Press the rinse aid compartment release button with your finger. 3. Fully open the rinse aid compartment lid. 4. Fill with rinse aid exactly up to the level marked “max”; this corresponds to a quantity of approx. 140 ml. 5. Close the lid and press until it locks into place. 6. Wipe up any spilt rinse aid with a cloth. Otherwise too much foam will be formed during the wash. Operating Instructions Adjusting Rinse Aid Dosing 3 As the dishes are washed rinse aid is released from the dispenser into the wash water. The dose is factory set at 4, and can be adjusted from 1 to 6. Only change the setting if streaks, milky spots or dried on water marks are visible on glasses or crockery. 0 1. Open the door of the dishwasher. 2. Press the rinse aid compartment release button with your finger. 3. Fully open the rinse aid compartment lid. 4. Set the dose level. 5. Close the lid and press until it locks into place. 6. If rins...