valutazioni - 4, GPA: 3.8
(
)
)
|
Facilità d'uso
-Tape Measure -Electric Drill -Torx (T-20) Head Screwdriver -1/8” Drill Bit -5/32” Drill Bit -Masking Tape -Safety Glasses -Original Installation Instructions Additional items required if using handle provided with dishwasher: -.” – 20 bolt, 2 .” long -.” Drill Bit ALL ELECTRICAL WIRING, GROUNDING AND PLUMBING SHOULD BE DONE IN ACCORDANCE WITH NATIONAL AND LOCAL CODES BY QUALIFIED INDIVIDUALS CHECK LOCAL PLUMBING CODES FOR APPROVED PLUMBING PROCEDURES AND ACCESSORIES. This appliance must be connected to a grounded metal, permanent wiring system; or an equipment-grounded conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance. This dishwasher is designed for operation on an individual 120 VAC, 60 Hz grounded electrical circuit. Use required fuse (15 amp) or comparable circuit breaker. Two wire with ground service to the dishwasher is recommended for connection at the terminal box and for grounding. 'LVFRQQHFWHOHFWULFDOSRZHUW. GLVKZDVKHUEHIRUH\RXVWDUW. )DLOXUHWRIROORZWKLVZDUQLQJFRXOG. 5HVXOWLQGHDWKRUVHULRXVLQMXU\. ..% $%!*+, !!$3!. !" !$$ )$ $!#& . ;$ *+9 $.0 2$%! !*+,$$. $ , 3! $9% . ! < $ ) $6;#% 5. 7 /',8" 9&!. = <( . 5:*. .. . !" !$#%"#& $' $'. (% $'!" !$)#&. $( +-, $. / 10 2,% . $$,$$!" !$$)45!$ & $. #6 % ('#&/$ $!10 7 /. 781" $9%&! ( . 5:*. Part No. 6 918803 A Step 1: Construct the Custom Panel. 1.1 Ensure the custom panel is the same size as the panel shown in the figure below. 1.2 Drill holes in the back of the panel using the template provided. Follow the instructions on the front of the template. If the template is missing follow the instructions on following page. Helpful Hint: Use masking tape on your drill bit to mark a maximum drill depth of 3/8”. 3/8” 1.2B Custom panel construction without a template. 1.2.1 Find the center of panel at the top and bottom and draw and line through both points, dividing the panel in two. 1.2.2 Drill two 1/8” holes per above figure no more than 3/8” deep. 1.2.3 Drill four 5/32” holes per above figure no more than 3/8” deep. Step 2: Installing Panel Fasteners. 2.1 Remove existing front panel from dishwasher. 2.1.1 Open door completely and remove the second screw from the top on both the right and left sides of the door. Save the screws. 2.1.2 Slide the existing front panel upward approximately 1 .”. Next pull the panel away from the dishwasher, separating it from the door. 2.2 Remove the two panel fasteners from the bottom of the front panel. 2.3 Remove the two panel fasteners from the face of the control panel on the inner door. 2.4 Screw each of the four panel fasteners into the four 5/32” pilot holes previously drilled into the back of the wood panel. Step 3: Mounting the Handle (Handle Provided with Dishwasher). See Step 3B for Custom Handle Installation. NOTE: Use these instructions ONLY if you are using the same handle provided with the dishwasher. You will need to purchase two . -20 bolts that are 2 . inches long. These can be found at any local hardware store. 3.1 Remove the handle from the front panel by removing the two screws from the back of the front panel. Discard the two large square washers. 3.2 Drill two .” holes thru the custom panel per figure below. These holes are also identified on the template. 3.3 Attach the handle to the custom panel with the two 2 . inch bolts. See figure above. NOTE: The large square washer should NOT be used with a custom panel. Step 3B: Mounting Custom Handles If using any type of custom handle it would be best to contact a professional cabinetmaker. All fasteners MUST be flush with the back of the panel to ensure a proper fit. Step 4: Mounting the Custom Panel to the Dishwasher. 4.1 Align the four panel fasteners with the four holes of the keyhole slots on the inner door panel. 4.2 Once all four fasteners are seated, slide the custom panel down until the top of the custom panel is flush with the top of the control panel. Check overall fit and appearance. 4.3 Open door completely and verify alignment one last time. Insert the two side screws into the existing holes, then drive them into the two 1/8” pilot holes of the custom panel. Step 5: Adjust Spring Tension on Door. 5.1 If the spring tension on the door is too great then lower the spring on the bracket. 5.2 If the spring tension on the door is not enough then: 5.2.1 Remove spring from bracket. 5.2.2 Remove the bracket by removing the two screws. 5.2.3 Drill two 5/32” holes one inch above the two existing screw holes in the collar frame. 5.2.4 Secure bracket to collar frame using the two new holes. Instructions pour panneaux personnalises Articles necessaires : -Panneau de facade personnalise pour porte (poids max. : 16 lb) o Le panneau DOIT avoir une epaisseur de 3/4 po. -Ruban a mesurer -Perceuse electrique -Tournevis Torx (T-20) -Foret de 1/8 po -Foret de 5/32 po -Ruban-cache -Lunettes de securite -Instructions d’i...