valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
3 Set the junction box cover, strain relief plate, and screw aside. They will be re-installed later. Figure 14 Figure 15 Door Panel Installation 1021" (533mm) 14" (355mm) Figure 19Hot Water Supply Line and Electrical Supply Cable Position in ChannelsABFigure 1625” (636 mm) 23-1/16” (586 mm) 1/4” max. (6 mm) Figure 17Figure 18 DOOR PANEL INSTALLATION Accessory Panel Installation Kits (select models) This kit allows you to install a custom panel (up to 1/4” thick) on your dishwasher. The panel dimensions are shown in Figure 16. Install the panel before sliding the dishwasher into place. Contact Customer Service to see if a kit is available for your model and to obtain ordering instructions. Fully Integrated Models Fully integrated models allow you to have a custom door panel made to match your cabinetry. The custom door can be a two-piece configuration to look like a drawer at the top and a cabinet door at the bottom or like a single full-length door. A template is included with the fully integrated models to explain the mounting procedure. NOTE: The door springs that are included with the Fully Integrated units will provide proper function for custom door panels weighing between 9 and 15 pounds. Custom Door panels weighing up to 18 pounds require the use of the Tension Adjustment Screws (See page 14 for details on the proper use of the Tension Adjustment Screws). Fig. 17 Dimension Integrated Panel Dimensions for Custom Door Panels A 27 3/16” - 30 7/16” (690mm - 774mm) B 23 3/16” - 23 3/8” (589mm - 594mm) PLACING THE DISHWASHER 1 Straighten and position the hot water supply line and the electrical supply cable as shown in Figure 18 so that they will align with their channels under the dishwasher base. 2 Position the dishwasher close enough to the enclosure so that you can run the dishwasher drain hose to the under sink drain connection. Make certain that the hot water supply line and the electrical supply cable are in their channels under the dishwasher base, as shown in Figure 19. 3 Slide the dishwasher into the opening making sure that the hot water supply line and the electrical supply cable stay in their proper channels. 4 Make sure the dishwasher is level. Adjust the rear leveler by turning the center screw at the front of the dishwasher, as shown in Figure 20a. Turning the screw clockwise raises the rear of the dishwasher. Adjust the front levelers by turning them with a screwdriver, as shown in Figure 20b. Turning the levelers to the right raises the dishwasher. If additional height is needed, shims may be added under the leveler feet. 11 SECURING THE DISHWASHER 1 Drive the mounting screws through the holes in the mounting brackets as shown in Figure 21 for Top or Side Mount. 2 After the unit is installed in the enclosure, leveled and secured, lock the two front leg levelers in place by driving the enclosed leg leveler locking screws into each screw boss located in front of the levelers. See Figure 22. 3 Tighten screws until they are flush with the surface of the bosses. a b Placing the Dishwasher/ Securing the Dishwasher Figure 21 Top Mount Side Mount Figure 20 Leg Leveler Locking Screw Screw Boss Figure 22 Installation of the Rubber Drain Hose Adaptor 1 Obtain the Rubber Drain Hose Adaptor and the two hose clamps from the Dishwasher Installation Kit (do not substitute). 2 On one outside end of the Rubber Drain Hose Adapter is a raised rib. Insert the dishwasher drain hose into the end without the raised rib (see Figure 23). Be sure to fully insert the drain hose. 3 Secure the connection with the Spring Clamp (see Figure 24). 4 Use the Screw Clamp to attach the Rubber Drain Hose Adaptor to the house plumbing (see Figure 24). Spring Clamp Screw Clamp Figure 24 Figure 23 Raised Rib Rubber Drain Hose Adaptor (cross section) Dishwasher Drain Hose Connects to household plumbing Insert until drain hose locks in place Raised Rib on Outside of Drain Hose Adaptor . . Drain Hose Connection/Hot Water Connection Figure 25MIN. 20" Non-Metallic Tie Connecting the Drain Hose to the Household Plumbing The dishwasher drain hose may be connected to the drain plumbing in one of four ways: 1 Directly to the undersink dishwasher drain connection, as shown in Figure 25. 2 Directly to a disposer dishwasher drain connection, as shown in Figure 26. 3 To the undersink dishwasher drain connection through an air gap, as shown in Figure 27. 4 To a disposer dishwasher drain connection through an air gap, as shown on Figure 28. Information on installing air gaps and disposers can Non-Metallic Tie MIN. 20" Figure 26 be found in the Plumbing Preparation section of this manual. IMPORTANT NOTES: · If the dishwasher drain hose is to be connected to a disposer dishwasher drain connection, remove the plug from the disposer’s dishwasher drain connection. · The dishwasher drain hose must have one place along its length that is securely attached 20 inches above the cabinet floor. · The drain hose length can be extended if necessary. The maxi...