valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
• The power cells in this unit cannot be replaced—once they reach the end of their service life, you must install a new Smoke Alarm. You must deactivate the unit before disposing of it. • Do not install this unit over an electrical junction box. Air currents around junction boxes can prevent smoke from reaching the sensing chamber and prevent the unit from alarming. Only AC powered units are intended for installation over junction boxes. • Do not stand too close to the unit when the alarm is sounding. It is loud to wake you in an emergency. Exposure to the horn at close range may harm your hearing. • Do not paint over the unit. Paint may clog the openings to the sensing chamber and prevent the unit from operating properly. 1 HOW TO INSTALL THIS SMOKE ALARM THE PARTS OF THIS SMOKE ALARM FOLLOW THESE SIMPLE STEPS! INSTALL THE MOUNTING BRACKET: 1. Locate the mounting bracket and find the two keyhole shaped slots marked “RPON” and “FGHI.” 2. Place the bracket on the wall or ceiling where you want to mount the alarm. 3. Hold the mounting bracket against the ceiling (or wall) and trace around the inside of the two keyhole slots labeled “RPON” and “FGHI”. (Fig. 1) 4. Make a mark inside each outline for the drill holes. Line one mark up with the letter “P” in the slot labeled “RPON,” and the other with the letter “H” in the slot marked “FGHI. This will help line your screws up correctly and make it easier to attach the mounting bracket. (Fig. 2) 5. Using a 3/16-inch (5 mm) drill bit, drill a hole through each pencil mark. 6. Insert the plastic screw anchors (in the plastic bag with screws) into the holes. Tap the screw anchors gently with a hammer, if necessary, until they are flush with the ceiling or wall. 7. Tighten the screws (provided) into the screw anchors, then loosen them 2 turns. 8. Hold the mounting bracket against the ceiling or wall so the large end of slot “RPON” slides over the mounting screw. Line the screw head up with the letter “P” printed on the bracket (in the narrow end of the keyhole slot). You will notice the bracket may not fit over the second screw. This is normal. 1 2 Parts of the Smoke Alarm Cover 1. Clear test button 2. Blue “Push To Silence” button Parts of the Smoke Alarm Cover 1. Mounting bracket 2. Keyhole Shaped Mounting Slot “RPON” 3. Keyhole Shaped Mounting Slot “FGHI” 4. Alignment Arrow On Mounting Bracket 5. Raised Activation Tab 6. Deactivation Tab (located under label) 7. Alignment Tab On Alarm 8. Turn to attach to bracket 9. Turn this way to remove from bracket Fig. 2Fig. 1 ACTIVATE THE POWER CELLS: You must activate the power cells before attaching the Smoke Alarm to the bracket. 1. Find the raised tab on the bottom of the alarm. 2. Insert a large coin or screwdriver in the slot. Turn clockwise (to the right) 1/2 turn until the tab comes out. This activates the power cells.If you have trouble activating the unit, call Consumer Affairs at: 1-800-323-9005 for assistance. NOTE: You may hear a “beep” when you remove the activation tab. This indicates the power cells have been activated correctly, but you must still test the unit using the test button to make sure it is working properly. 3. Test the Smoke Alarm. Press and hold the test button on the cover of the unit until the alarm sounds (the unit may continue to alarm for a few seconds after you release the button). During testing, you will hear a loud, repeating horn pattern: 3 beeps, pause, 3 beeps, pause. If the unit does not alarm during testing, call Consumer Affairs for assistance. ATTACH SMOKE ALARM TO MOUNTING BRACKET 1. Line up the alignment tab on the unit with the alignment tab on the mounting bracket. Push the unit toward the bracket, and turn it clockwise until you feel it snap into place. 2. Test the unit again. Press the clear test button until the horn begins sounding. During testing, you will hear a loud, repeating horn pattern: 3 beeps, pause, 3 beeps, pause. TOOLS YOU WILL NEED: This unit is designed to be mounted on the ceiling, or on the wall if necessary. • Pencil • Drill with 3/16” (5 mm) drill bit • Standard flathead screwdriver • Hammer 9. Rotate the mounting bracket (to the right) until it fits around the second screw head. Then move the bracket so the second screw lines up with the “H” printed on the bracket. 10. Tighten both screws all the way. HOW TO INSTALL THIS SMOKE ALARM THE PARTS OF THIS SMOKE ALARM FOLLOW THESE SIMPLE STEPS! INSTALL THE MOUNTING BRACKET: 1. Locate the mounting bracket and find the two keyhole shaped slots marked “RPON” and “FGHI.” 2. Place the bracket on the wall or ceiling where you want to mount the alarm. 3. Hold the mounting bracket against the ceiling (or wall) and trace around the inside of the two keyhole slots labeled “RPON” and “FGHI”. (Fig. 1) 4. Make a mark inside each outline for the drill holes. Line one mark up with the letter “P” in the slot labeled “RPON,” and the other with the letter “H” in the slot marked “FGHI. This will help line your screws up correctly...
Questo manuale è adatto anche per i modelli :allarme antincendio - 4010YR (319.92 kb)