valutazioni - 2, GPA: 5
(
)
)
|
Facilità d'uso
TO LOCK THE MOUNTING BRACKET 1. Using needle-nose pliers, detach one locking pin from mounting bracket. 2. Insert the locking pin into the lock located opposite from the battery drawer as shown in the diagram. 3. When you attach the Smoke Alarm to the mounting bracket, the locking pin’s head will fit into a notch on the bracket. Locking Features (Continued) Printed in Mexico M08-0050-003 Q 04/07 First Alert® is a registered trademark of the First Alert Trust. BRK® is a registered trademark of BRK Brands, Inc. WEEKLY TESTING • NEVER use an open flame of any kind to test this unit. You might accidentally damage or set fire to the unit or to your home. The builtin test switch accurately tests the unit’s operation as required by Underwriters Laboratories, Inc. (UL). • If the Alarm ever fails to test properly, replace it immediately. Products under warranty may be returned to the manufacturer for replacement. See “Limited Warranty” at the end of this manual. DO NOT stand close to the Alarm when the horn is sounding. Exposure at close range may be harmful to your hearing.When testing, step away when horn starts sounding. It is important to test this unit every week to make sure it is working properly. Using the test button is the recommended way to test this Smoke Alarm. Press and hold the test button on the cover of the unit until the alarm sounds (the unit may continue to alarm for a few seconds after you release the button). If it does not alarm, make sure the unit is receiving power and test it again. If it still does not alarm, replace it immediately. During testing, you will hear a loud, repeating horn pattern: 3 beeps, pause, 3 beeps, pause. When testing a series of interconnected units you must test each unit individually. Make sure all units alarm when each one is tested. REGULAR MAINTENANCE Use only the replacement batteries listed below. The unit may not operate properly with other batteries. Never use rechargeable batteries since they may not provide a constant charge. This unit has been designed to be as maintenance-free as possible, but there are a few simple things you must do to keep it working properly: • Test it at least once a week. • Clean the Smoke Alarm at least once a month; gently vacuum the outside of the Smoke Alarm using your household vacuum’s soft brush attachment. Test the Smoke Alarm. Never use water, cleaners or solvents since they may damage the unit. • If the Smoke Alarm becomes contaminated by excessive dirt, dust and/or grime, and cannot be cleaned to avoid unwanted alarms, replace the unit immediately. • Relocate the unit if it sounds frequent unwanted alarms. See “Locations To Avoid For Smoke Alarms” for details. • Model 7010B Only: When the battery back-up becomes weak, the Smoke Alarm will “chirp” about once a minute (the low battery warning). This warning should last 7 days, but you should replace the battery immediately to continue your protection. Model 7010B Only – Choosing a replacement battery: Your Smoke Alarm requires one standard 9V battery. The following batteries are acceptable as replacements: Duracell #MN1604, (Ultra) #MX1604; Eveready (Energizer) #522. You may also use a Lithium battery like the Ultralife U9VL-J for longer service life between battery changes. These batteries are available at many local retail stores. Actual battery service life depends on the smoke alarm and the environment in which it is installed. All the batteries specified above are acceptable replacement batteries for this unit. Regardless of the manufacturer’s suggested battery life, you MUST replace the battery immediately once the unit starts “chirping” (the “low battery warning”). UNDERSTANDING THE INDICATOR LIGHTS AND ALARM HORN PATTERNS NOTE: When power is applied, unit(s) may alarm momentarily. *When any Smoke Alarm in an interconnected series triggers an alarm, its red LED will flash rapidly. The red LEDs will remain OFF on any remaining alarms in the series. This feature helps responders identify which unit(s) triggered the alarm. AC Power All Models DC Power Model 7010B Normal Operation Constant Green LED Flashing Red LED approx. once/minute No Audible Alarm Green LED Off Flashing Red LED approx. once/minute No Audible Alarm Test Condition Constant Green LED Rapidly Flashing Red LED Audible Alarm Green LED Off Rapidly Flashing Red LED Audible Alarm Silence Mode Red LED flashes once every 10 seconds Red LED flashes once every 10 seconds Alarm Condition* (Initiating Unit) Constant Green LED Rapidly Flashing Red LED Audible Alarm Green LED Off Rapidly Flashing Red LED Audible Alarm IF THIS SMOKE ALARM SOUNDS RESPONDING TO AN ALARM During an alarm, you will hear a loud, repeating horn pattern: 3 beeps, pause, 3 beeps, pause. • If the unit alarms and you are not testing the unit, it is warning you of a potentially dangerous situation that requires your immediate attention. NEVER ignore any alarm. Ignoring the alarm may result in injury or death. • Never disconnect the AC power to qu...
Questo manuale è adatto anche per i modelli :allarme antincendio - 7010BUS (903.04 kb)