valutazioni - , GPA: ( )

Istruzioni per l'uso Bacharach, Modello KN-COPD-3-UK

Produttore : Bacharach
File Size : 308.57 kb
File Nome : 900-0211UK.pdf

Lingua di insegnamento:

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Il documento viene caricato, si prega di attendere

Scarica la tua primo

If you have any questions about the operation or installation of your alarm, please call Kidde Safety Europe on 01753 685148 820-1196 REV. A 2520-7203-00 2520-7203-00.qxd 2006.4.7 3:50 PM Page 2 Table of Contents Quick Set Up Guide Introduction • Carbon Monoxide Features • Your CO alarm • What CO alarms can and cannot do Installation • Where to install your alarm • Where not to install your alarm • How to install your alarm Normal Operation • Normal operating characteristics • How to test the electronics • How to know if your alarm is malfunctioning • How to care for your alarm What You Should Know Before the Alarm Sounds • The effects of CO exposure • Your family can be at risk for CO poisoning • Where CO comes from • What you can do to protect your family • Home safety tips • Determine if anyone in the household is at high risk for CO poisoning The Effects of Carbon Monoxide Exposure • Understand the effects of carbon monoxide exposure What to Do When the Unit Alarms • How to respond to the alarm • Who you should call if you suspect you have CO or in your home • Sometimes it is difficult to find the source of CO Technical Information • Product Specifications • How the unit determines when to alarm • Display Readings Warranty • Warranty Environmental Protection Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with Local Authorityor retailer for recycling advice. 2520-7203-00.qxd 2006.4.7 3:50 PM Page 1 IMPORTANT THIS CARBON MONOXIDE ALARM IS DESIGNED TO DETECT CARBON MONOXIDE GAS FROM ANY SOURCE OF IMPROPER OR MALFUNCTIONING APPLIANCES. IT WILL NOT SENSE SMOKE, FIRE, OR ANY POISONOUS GAS OTHER THAN CARBON MONOXIDE. FOR THIS REASON YOU MUST INSTALL SMOKE ALARMS TO PROVIDE EARLY WARNING OF FIRE AND TO PROTECT YOU AND YOUR FAMILY FROM FIRE AND ITS RELATED HAZARDS. WARNING! THIS UNIT IS NOT A SMOKE ALARM. IT WILL NOT SENSE SMOKE OR FIRE. IT IS NOT A SUBSTITUTE FOR INSTALLING AND MAINTAINING AN APPROPRIATE NUMBER OF SMOKE ALARMS IN YOUR HOME. FOR EARLY WARNING OF FIRE, YOU MUST INSTALL SMOKE ALARMS EVEN THOUGH CARBON MONOXIDE CAN BE GENERATED BY FIRE. THIS PRODUCT IS INTENDED FOR USE IN ORDINARY INDOOR RESIDENTIAL AREAS. IT IS NOT DESIGNED TO MEASURE COMPLIANCE WITH COMMERCIAL AND INDUSTRIAL STANDARDS. THE INSTALLATION OF THIS DEVICE SHOULD NOT BE USED AS A SUBSTITUTE FOR PROPER INSTALLATION, USE AND MAINTENANCE OF FUEL-BURNING APPLIANCES, INCLUDING APPROPRIATE VENTILATION AND EXHAUST SYSTEMS. INDIVIDUALS WITH MEDICAL PROBLEMS MAY CONSIDER USING WARNING DEVICES WHICH PROVIDE AUDIBLE AND VISUAL SIGNALS FOR CARBON MONOXIDE CONCENTRATIONS UNDER 30 PPM. THIS ALARM WILL NOT WORK WITHOUT POWER. THIS ALARM REQUIRES A CONTINUOUS SUPPLY OF POWER. DURING A POWER OUTAGE, UNIT WILL OPERATE FOR AT LEAST 20 HOURS ON A 9 VOLT BATTERY WITH FULL CAPACITY. ELECTRICAL SHOCK OR MALFUNCTION MAY OCCUR IF TAMPERED WITH, OR NOT INSTALLED IN ACCORDANCE WITH MANUFACTURERS INSTRUCTIONS. 1 2520-7203-00.qxd 2006.4.7 3:50 PM Page 2 Quick Set Up Guide We urge you to read this entire manual in the sequence it is presented. Listed below are five easy steps for setting up your Kidde CO Alarm. Please read this entire guide for complete information. Note: This CO alarm must be installed by a competent person. Step 1 -Determine the best location for your CO alarm(s). Refer to Installation, Where to Install Your Alarm for complete information. Step 2 -Install the 9 volt backup battery. To install the battery, open the back cover and snap the battery connector onto the battery. You will hear the alarm sound briefly to indicate the unit is receiving power. At power up, you will see a flashing red dot and three eights in the digital display indicating the alarm is warming up. After approximately 20 seconds the unit will start sampling for CO. During this period a number will appear on the digital display. The number on the digital display should be zero (0). See “Normal Operating Characteristics” for complete information on operating characteristics. Place the battery into the battery compartment and replace the back cover. IMPORTANT! A small screwdriver or similar tool may be required to remove the back cover. The back cover should be levered up from the centre recess at the bottom of the alarm. The cover is designed this way to discourage the removal of batteries, or tampering, by young children. Step 3 -Determine how you want to mount the alarm. Your CO alarm is equipped to be mounted as a corded, a direct plug, or a table top unit. Refer to Installation, How to Install your Alarm for complete instructions about how to configure your alarm for installation. Step 4 -Install the alarm. Plug the alarm into a standard un-switched 230 volt AC electrical outlet in one of the alarm configurations listed in step 3. Wait 2 to 3 minutes after power up and make sure the red dot in the digital display is blinking. Step 5 -Test the unit’s operation by pressing and releasing the Test/Reset but...