Gals 291.5 (min) 375 (max) L Electrical Specifications Each component requires a separate, dedicated GCFI protected circuit Motor/Pump 120V 20A 60HZ Heater 120V 15A 60HZ FEATURES, UPGRADES & ACCESSORIES Material Type: High-Gloss Acrylic Install Type: Drop-in with wood frame or Undermount Available Colors: White (W), Almond (A), Oyster (Y), Black (B) Cut-out: 69” x 33” or Undermount Template DD42000 Standard (Included) Features: 14 jets, In-line Heater, Chromatherapy lighting, infinity e

Cut along the dotted lines and place the corrugated protector over the top and front of the tub. The center cut-out drops into the center of the tub. After measuring the dimensions of the product, frame the construction area. Locate the tub in position and mark a joist so that a 2x4 stringer can be nailed in place. The stringer will be located under the flange against the wall. Nail in place the 2x4 support. Re-position the tub and check for level, both front to back and left to right. It ma

Always check to make sure that the Elevated Toilet Seat is properly and securely locked in place before using. Ensure that all four (4) mounting brackets are adjusted to the same height-otherwise injury or damage may occur. Be sure to center your weight on the Elevated Toilet Seat because the seat may tip if you lean too far forward or to either side. Users with limited physical capabilities should be supervised or assisted when using the Elevated Toilet Seat. The Elevated Toilet Seat has a reco

If you are unable to understand these Warnings, Cautions and Instructions, contact a healthcare professional, dealer or technical personnel if applicable before attempting to install this equipment - otherwise, injury or damage may occur. Use the arm supports ONLY for assistance. DO NOT attempt to use the arms to support full body weight. Always check to make sure that the Raised Toilet Seat is properly and securely locked in place before using. Make certain that the knob that secures the Raised

If you are unable to understand these Warnings, Cautions and Instructions, contact a healthcare professional, dealer or technical personnel if applicable before attempting to install this equipment - otherwise, injury or damage may occur. Use the arm supports ONLY for assistance. DO NOT attempt to use the arms to support full body weight. Always check to make sure that the Raised Toilet Seat is properly and securely locked in place before using. Make certain that the knob that secures the Raised

1.1 Recommended Tools Tape Measure Regular Screwdriver Phillips Screwdriver CARE INSTRUCTIONS: DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH. DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE. TOWEL RING, ROBE HOOK and TISSUE HOLDER MOUNTING BRACKET INSTALLATION The TOWEL RING, ROBE HOOK and TISSUE HOLDER work best if secured to a wall stud or cross brace within the wall, using 1-1/

1.1 Recommended Tools Tape Measure Regular Screwdriver Phillips Screwdriver CARE INSTRUCTIONS: DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH. DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE. TOWEL RING, ROBE HOOK and TISSUE HOLDER MOUNTING BRACKET INSTALLATION The TOWEL RING, ROBE HOOK and TISSUE HOLDER work best if secured to a wall stud or cross brace within the wall, using 1-1/

If MOUNTING BRACKET (1) is secured to a stud or cross brace drill small pilot holes for SCREWS (3). (NOTE PROPER POSITION OF MOUNTING BRACKET FOR ACCESSORY TO BE INSTALLED.} For installations on drywall or tiled walls, use ANCHORS (4) and SCREWS (2) for securing MOUNTING BRACKETS (1) to wall. Use MOUNTING BRACKET (1) as a template and mark the mounting holes. Drill three 1/8" diameter holes a minimum of 1-1/4" deep. Insert the three ANCHORS (4) flush with face of the finished wall. Secure MOUN

Secure accesory with SET SCREW (3) using 2.5mm HEX WRENCH (4) supplied. (NOTE POSITION OF MOUNTING BRACKET.} 2 POSITION OF MOUNTING BRACKET FOR TOWEL RING AND ROBE HOOK 2 ROBE HOOK AND TISSUE HOLDER INSTALLATION Align accessory (C, D) and place ESCUTCHEON (1) onto MOUNTING BRACKET (2). Secure accesory with SET SCREW (3) using 2.5mm HEX WRENCH (4) supplied. (NOTE POSITION OF MOUNTING BRACKET.} 3 2 HOOK AND TISSUE HOLDER M968630 Rev. 1 .1