Cut along the dotted lines and place the corrugated protector over the top and front of the tub. The center cut-out drops into the center of the tub. After measuring the dimensions of the product, frame the construction area. Locate the tub in position and mark a joist so that a 2x4 stringer can be nailed in place. The stringer will be located under the flange against the wall. Nail in place the 2x4 support. Re-position the tub and check for level, both front to back and left to right. It ma
Your new bath is shipped to you after careful inspection. The whirlpool and air bath versions are completely assembled with pump/blower and system piping. All you need to finish the installation are your selected fittings and electrical connections. To ensure maximum performance and pleasure from this product, please follow the instructions and cautions. For questions or service issues, please call Technical Support 1-(800)-442-1902. Please do not contact or return product to the store. © AS Ame
(219 kg/sq.m) Weight with Water / Floor Loading 57 lb. (26 kg.) Product Weight 54 gal. (246 l.) Gallon to Overflow Whirlpool Operating Volume 3582 Serin 5-1/2' x 36" L 66" (1676mm) W 36" (914mm) H 23" (584mm) A 16-7/8" (429mm) B 9-3/4" (248mm) C 20" (508mm) 64-1/2" (1638mm) x 34-1/2" (876mm) 66-3/16" (1681mm) x 34-1/2" (876mm) 806 lb. (365 kg)/ 49 lb./sq.ft. (239 kg/sq.m) 65 lb. (29 kg.) 97 gal. (441 l.) 3583 Serin Oval L 68" (1727mm) W 38" (965mm) H 23" (584mm) A 17-1/4" (438mm) B 11-1/2" (292m
A31 ELECTRICAL INSTALLATION INSTRUCTIONS (continued) ELECTRONIC ACTIVATED COMBINATION TUB WITH LIGHTS (4 BUTTON PANEL) 120V, 60HZ 15A GFCI (FOR HEATER) ELECTRICAL FEED GFCI 120V, 60HZ 15A GFCI ELECTRICAL FEED GFCI 120V, 60HZ 15A GFCI ELECTRICAL FEED GFCI ELECTRICAL INSTALLATION INSTRUCTIONS (continued) USE THREE JUNCTION BOXES (CANADA MARKET) ECOSILENT PUMP HAS P3JJ PLUG WHIRLPOOL HEATER IS FACTORY INSTALLED ON COMBINATION TUBS Green/Copper Black White Green/Copper Black White Green/Copper Black
The cycle will start on white. • Turn off and on within 3 seconds; it will change to slow rainbow cycle and so on per the display color table shown above. 754532-100 Rev. A 40 Operation: Combination Tub with Lights (continued) EXITING THE BATH • Be sure to turn off the air blower before draining bath. • Open drain by rotating drain knob clockwise. DRYING CYCLE OPTIONS STANDARD DRYING CYCLE An automatic drying cycle will start 20 minutes after the blower is turned off. The blower LED blinks while
Attach the 8 AWG solid copper conductor supplied with the heater from the heater bonding lug to the motor frame bonding lug as shown in Figure 3. The conductor is secured to the lugs using set screws. The motor frame shall have a second 8 AWG solid copper conductor connected from the frame bonding lug to the home’s electrical panel or approved local bonding point as shown in Figure 3. NOTE: For all “EcoSilent” pump configurations, the pump housing is plastic. Therefore, the first copper conducto
It will only turn the heater off if the thermostat fails. If the high-limit trips frequently, call a service technician. To manually reset the circuit in the event that the “High-Limit” switch has been activated, simply (1) Turn off the whirlpool pump. (2) Drain water from the tub. (3) Remove power from heater by unplugging at receptacle or turning off circuit breaker. (4) The heater circuit will automatically reset in less than 15 minutes. (5) Restore power to the heater. (6) Whirlpool bath is
TO CONTROL PANEL TO BLOWER 3. 754025-0073A CABLE EXISTING (INCLUDES ADAPTER CABLE BOX SHOWN) REMOTE BLOWER LOCATION OPTION (continued) FOR THE COMBINATION WHIRLPOOL / AIR BATH CONFIGURATIONS ONLY: Up to two additional control box extensions (P/N 754512-0070A) are required as shown in photo 4 (below). Simply extend the cables going to the blower by adding in the extension cables. Be careful not to damage the cable connections and never plug in cables while power is applied to blower and/or pump.
(448 kg)/ 130 lb. 103 gal. 65 gal. Studio (5/8") W 61-3/8" (1559mm) (381mm) (530mm) 27 lb./sq.ft. (59 kg.) (390 l.) (246 l.) Corner H 21-1/2" (546mm) B 13-1/2" (133 kg/sq.m) (343mm) 2944 2" L 84-1/4" (2139mm) A 15" C 19-1/2" N/A 988 lb. (448 kg)/ 130 lb. 103 gal. 65 gal. Studio W 31-13/16" (808mm) (381mm) (495mm) 27 lb./sq.ft. (59 kg.) (390 l.) (246 l.) Corner H 21-1/2" (546mm) B 13-5/8" (133 kg/sq.m) (346mm) TABLE 7 ROUGH-IN REFERENCES MODEL SERIES 2944 59-3/4" NOMINAL (1518mm) 9" x 18" (229 x
SPECIFICATIONS: L W H C SIDE VIEW END VIEW DRAIN / OVERFLOW ABJ GENERAL SPECIFICATIONS FOR WHIRLPOOLS AND BATH TUBS Description Dimensions L-W-H Drain / Overflow Height to Underside of Deck: C Cut Out Pier G x F Rough-In Recess E x D Tub Edge to Centerline Overflow: J Weight with Water / Floor Loading Product Weight Gallon to Overflow Whirlpool Operating Volume 2664 Scala Corner L 83-1/2" (2121mm) W 63-3/4" (1619mm) H 19-3/4" (502mm) A 16" (406mm) B 13-1/4" (337mm) C 18-1/4" (464mm) Template Pro