|
Facilità d'uso
Remove misfed paper. While pushing the release lever, remove the finisher. Hold up lever R3 and remove misfed paper. If you can not remove misfed paper, open the lower front cover. While pushing knob R5, turn knob R5 clockwise. Hold up the lever on the upper right of the booklet tray, and open the cover. Remove misfed paper. Close the cover. Turn knob R4 counterclockwise. Note Depending on the location of misfed paper, knob R4 might not turn. If you can not remove misfed paper, hold up lever R1 and remove misfed paper. Hold up lever R2 and remove misfed paper. Lower the finisher proof tray, and close the upper cover. While pushing the release lever, remove the finisher. Remove misfed paper. Return the release lever until it clicks, and attach the finisher. 1 3 4 5 6 7 8 2 1 2 3 4 5 6 7 8 When R is lit 280 x Clearing Misfeeds ZBQY250E 281 What to Do If Something Goes Wrong Changing the Paper Size Important . If you wish to change the paper size set in tray 1, tray 3, and the optional large capacity tray (LCT), contact your service representative. Reference For paper sizes, weight, and capacity that can be set in each tray, see . P.23 “Copy Paper”. Changing the Paper Size in Tray 2 A Make sure that the paper tray (tray 2) is not being used. Then fully pull out the tray. Remove the paper in the tray. ZBQY140E B While pushing the release lever, adjust the side fences and back fence to the new paper size. ZBQY150E 282 Changing the Paper Size C Square the paper and set it in the tray. ZBQY050E Important r Do not stack paper over the limit mark. r Make sure that the paper stack is flush with the right side fence. Note 5 r Straighten the paper, if curled or warped, before placing it in the tray. D Set the paper size selector inside the tray to the new paper size. ZBQY160N To adjust the paper size to one not available with the paper size selector A Set the paper size selector knob to the p mark on the left. B Press the {User Tools/Counter}key. C Press the [System Settings] key. D Press the [Paper Size Setting] key. E Press the [Tray 2:Paper Size Setting] key. F Select your desired size. Then, press the [OK] key. G Press the [Exit] key or press the {User Tools/Counter} key to exit the User Tools. 283 What to Do If Something Goes Wrong Important . Be sure to select paper size with the User Tools (System Settings). Otherwise, misfeeds might occur. Reference For details, see “User Tools (System Settings)” in the System Settings manual. E Gently push the paper tray until it stops. F Check the paper size displayed on the display panel. 284 d Adding Staples dAdding Staples RCAUTION: • Our products are engineered to meet high standards of quality andfunctionality, and we recommend that youonly use the expendable supplies available at an authorized dealer. Important . If you use a staple cartridge other than that recommended, staple failure or staple jams might occur. Note . If the optional booklet finisher is installed, initialize the staple unit for the Saddle Stitch function with the User Tools (System Settings) after adding staples or removing jammed staples. If you do not, misfeeds might occur. See “Staple initialization” in the System Settings manual. 50-Sheet Finisher • 1: Open the front cover of the finisher. R7 • 2: Pull out the staple unit. ZBQP510E • 3: Lift the cartridge until it clicks. ZBQP520E 285 What to Do If Something Goes Wrong • 4: Pull out the cartridge gently. ZBQP530E • 5: Take out the empty refill in the direction of the arrow. • 6: Align the arrows on the new refill and the cartridge, then push in the refill until it clicks. • 7: Pull out the ribbon. ZBQP540E ZBQP550E ZBQP560E 286 d Adding Staples • 8: Reinstall the cartridge. ZBQP580E ZBQP570E • 9: Press down the cartridge until it clicks. • 10: Bring the staple unit back into 5 place. • 11: Close the front cover of the finisher. ZBQP590E 100-Sheet Finisher • 1: Open the front cover of the finisher. ZBQP200E 287 What to Do If Something Goes Wrong ZBQP210E ZBQP220E ZBQP230E ZBQP240E • 2: Pull lever R8 down in the staple unit. • 3: Turn knob R9 until the staple unit rises. • 4: Pull out the staple unit lever. • 5: Pull out the staple unit gently. • 6: Put down the staple unit on a level surface. • 7: Raise the cover up. • 8: Set the new refill. ZBQP250E 288 d Adding Staples • 9: Lower the cover until it clicks. ZBQP260E ZBQP270E • 10: Pull out the ribbon. • 11: Turn the staple unit around. ZBQP280E • 12: Reinstall the staple unit. ZBQP290E • 13: Push the staple unit until it clicks. ZBQP300E 289 What to Do If Something Goes Wrong • 14: Close the front cover of the finisher. ZBQP310E Booklet Finisher 1 2 R6 ZBQP020E ZBQP030E ZBQP040E • 1: Open the front cover of the finisher. • 2: Pull lever R6 down, then pull out the cartridge while lifting the cartridge. • 3: Take out the empty refill in the direction of the arrow. • 4: Set the new refill. • 5: Pull out the ribbon. ZBQP050E 290 d Adding Staples • 6: Push the cartridge until it clicks. • 7: Close the ...
Questo manuale è adatto anche per i modelli :Stampanti - 700 (4.84 mb)