valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
1.00 - 8 - 1-2-2 Parallel Interface (IEEE1284) SRP-F310/312 Pin No. Source Compatibility Mode Nibble Mode Byte Mode 1 Host nStrobe HostClk HostClk 2 Host / Printer Data 0 (LSB) - Data 0 (LSB) 3 Host / Printer Data 1 - Data 1 4 Host / Printer Data 2 - Data 2 5 Host / Printer Data 3 - Data 3 6 Host / Printer Data 4 - Data 4 7 Host / Printer Data 5 - Data 5 8 Host / Printer Data 6 - Data 6 9 Host / Printer Data 7 (MSB) - Data 7 (MSB) 10 Printer nAck PtrClk PtrClk 11 Printer Busy PtrBusy /Data3,7 PtrBusy 12 Printer Perror AckDataReq/Data2, 6 AckDataReq 13 Printer Select Xflag /Data 1,5 Xflag 14 Host nAutoFd HostBusy HostBusy 15 NC NC NC 16 GND GND GND 17 FG FG FG 18 Printer Logic-H Logic-H Logic-H 19~30 GND GND GND 31 Host nInit nInit nInit 32 Printer nFault nDataAvail /Data0,4 nDataAvail 33 GND ND ND 34 Printer DK Status ND ND 35 Printer +5V ND ND 36 Host nSelectIn 1284-Active 1284-Active Rev. 1.00 - 9 - SRP-F310/312 1-2-3 USB Interface Pin No. Signal Name Assignment (Color) Function Shell Shield Drain Wire Frame Ground 1 VBUS Red Host Power 2 D- White Data Line(D-) 3 D+ Green Data Line(D+) 4 GND Black Signal Ground 1-3 Connecting the Drawer 1 6 * WARNING Use a drawer that matches the printer specification. Using an improper drawer may damage the drawer as well as the printer. * CAUTION Do not connect a telephone line to the drawer kick-out connector; otherwise the printer and the telephone line may be damaged. Plug the drawer cable into the drawer kick-out connector on the back of the printer next to the power supply connector. Pin No. Signal name Direction 1 Frame ground - 2 Drawer kick- out drive signal 1 Output 3 Drawer open/close signal Input 4 +24V - б Drawer kick- out drive signal 2 Output б Signal ground - Rev. 1.00 - 10 - SRP-F310/312 1-4 Setting the Dip Switches 1-4-1 Serial Interface SW Function ON OFF Default 1-1 Auto-Cutter Selection Disable Enable OFF 1-2 Handshaking XON/OFF DTR/DSR OFF 1-3 Word length 7 bits 8 bits OFF 1-4 Parity check Yes No OFF 1-5 Parity selection EVEN ODD OFF 1-6 Baud rate selection Refer to the Following Table 1 OFF 1-7 ON 1-8 OFF D P switch 1 Setting Function Transmission speed SW1 - 6 SW1 - 7 SW1 - 8 Default 2400 baud ON OFF OFF 9600 4800 baud ON OFF ON 9600 baud OFF ON OFF 19200 baud OFF OFF OFF 38400 baud OFF ON ON 57600 baud OFF OFF ON 115200 baud ON ON ON Table 1 - Baud Rate Selection 1-4-2 Parallel & USB Interface SW Function ON OFF Default 1-1 Auto-Cutter Selection Disable Enable OFF 1-2 1-8 Reserved - - OFF DI P switch 1 Setting Function & Auto Cutter Enable / Disable selection Dip Switch Set 1 SW1 - 1 ON Auto Cutter Disable OFF Auto Cutter Enable Application Ignores Auto Cutter error for continuous printing Rev. 1.00 - 11 - SRP-F310/312 1-5 Installing or Replacing the Paper Roll * NOTE Be sure to use paper rolls that meet the specifications. Do not use paper rolls that have the paper glued to the core because the printer cannot detect the paper end correctly. 1-5-1 Make sure that the printer is not receiving data; otherwise, data may be lost. 1-5-2 Open the paper roll cover by pressing the Push button. * NOTE Do not open the print cover while the printer is operating. This may damage the printer. 1-5-3 Remove the used paper roll core if there is one. 1-5-4 Insert the paper roll as shown. Rev. 1.00 - 12 - SRP-F310/312 1-5-5 Be sure to note the correct direction that the paper comes off the roll. O x 1-5-6 Pull out a small amount of paper, as shown. Then close the cover. * NOTE When closing the cover, press the center of printer cover firmly to prevent paper miss-loading. 1-5-7 Tear off the paper as shown. Rev. 1.00 - 13 - SRP-F310/312 1-6 Adjustments and Settings The SRP-F310 is set up at the factory to be appropriate for almost all users. It does, however, offer some settings for users with special requirements. It has DIP switches that allow you to change communication settings, such as handshaking and parity check, as well as print density. The SRP-F310 also has a near-end sensor for the paper. This can give you a warning when the paper is almost out. If you find that there is not enough paper remaining on the roll when the near-end sensor is triggered, you can change the near-end sensor setting. Rotate the near end sensor tab at front or rear position. (See the below figure) 1-7 Using the Printer Control Panel POWER ERROR PAPER O POWER The POWER light is on whenever the printer is on. O ERROR This indicates an error. O PAPER This light indicates the near end of the paper roll. Install a new paper roll and the printer will continue printing. When the light blinks, it indicates the self-test printing standby state or macro execution Standby state when the macro execution command is used. O FEED Press the FEED button once to advance paper one line. You can also hold down the FEED button to feed paper continuously. ...
Questo manuale è adatto anche per i modelli :Stampanti - SRP-F310 (682.94 kb)
Stampanti - SRP-F312 (682.94 kb)
Stampanti - SRP-F312 (682.94 kb)