valutazioni - 4, GPA: 3.3
(
)
)
|
Facilità d'uso
When making two-sided copies, the multi-bypass tray cannot be used. A AA A A A A A Turn on Long Edge Turn on Short Edge Making two-sided copies Place the original(s) on the document glass or in the SPF. (see "ORIGINAL PLACEMENT" (p.47). 1 2 Select two-sided copy mode. When copying in a one-sided to two-sided mode: Use the original to copy key to select the desired one-sided to two-sided copying mode (Turn on Long Edge or Turn on Short Edge). See the illustrations on page 52. 3 Select the copy settings. See "SET THE COPY QUANTITY" (p.49), "EXPOSURE ADJUSTMENT/PHOTO COPYING" (p.49), and "REDUCTION/ENLARGEMENT/ZOOM" (p.51). Using the document glass Press the start ( ) key. 1 The original is scanned into the unit's memory and the number of the copy quantity blinks in the display. Place the original that you wish to copy onto the rear side of the 2 paper, and press the start ( ) key again. Copying begins. 6 Using the SPF Press the start ( ) key. Copying begins in the selected two-sided copy mode. DESCRIPTION OF OTHER SPECIAL FUNCTIONS Toner save mode Reduces toner consumption by approximately 10%. Power save modes The unit has two power save modes of operation: preheat mode and auto power shut-off mode. Preheat mode When the unit enters the preheat mode, the power save ( ) indicator will light up and other indicators will remain on or off as before. In this condition, the fuser in the unit is maintained at a lower heat level, thereby saving power. To copy from the preheat mode, make desired copier selections and press the start ( ) key using the normal copying procedure. Auto power shut-off mode When the unit enters the auto power shut-off mode, the power save ( ) indicator will light up and other indicators except the ONLINE indicator will go out. The auto power shut-off mode saves more power than the preheat mode but requires a longer time before starting copying. To copy from the auto power shut-off mode, press the start ( ) key. Then make desired copier selections and press the start ( ) key using the normal copying procedure. Auto clear The unit returns to the initial settings a preset amount of time after the end of job. This preset amount of time (auto clear time) can be changed. Resolution of AUTO & MANUAL mode You can set the copy resolution used for AUTO and MANUAL ( ) exposure mode. Prevention of OC copies when the SPF is up function When enabled, this function may help prevent wasteful use of toner that occurs when the OC cover is not completely closed. If the start ( ) key is pressed when the OC cover is not completely closed, " " will appear in the display and copying may not take place. If copying does not take place, copying can be performed by pressing the start ( ) key again, however, the scan size set in "Copy effective paper width setting function" (program numbers 25, 26, 27) will be used. If the OC cover is completely closed after " " appears, copying will take place at the normal size. TONER SAVE MODE 1 Press the exposure mode selector key to select the MANUAL ( ) mode. 2 Press and hold down the exposure mode selector key for approximately 5 seconds. The MANUAL ( ) indicator will go out and the PHOTO ( ) indicator will begin to blink. The light and dark indicator marked "5" will light up, indicating the standard toner mode is active. 3 To enter the toner save mode, press the light ( ) key. The light and dark indicator marked "1" will light up, indicating the toner save mode is selected. 4 Press the exposure mode selector key. The PHOTO ( ) indicator will stop blinking and light up steadily. The light and dark indicator marked "3" will light up. The toner save mode is now active. To return to the standard mode, repeat the procedure but use the dark ( ) key to select exposure level "5" in step 3. USER PROGRAMS The user programs allow the parameters of certain functions to be set, changed, or canceled as desired. Setting the user programs 1 2 3 4 Press and hold down the light ( ) key simultaneously for more than 5 seconds until all the alarm indicators ( , , ) blink and " " appears in the display. Use the left copy quantity ( ) key to select a user program number (For the user program numbers, see the following table.). The selected number will blink in the left side of the display. 6 Press the start ( ) key. The entered program number will be steadily lit and the currently selected parameter number for the program will blink on the right side of the display. Select the desired parameter using the right copy quantity ( ) key. The entered parameter number will blink on the right of the display. Program No. Mode Parameters 1 Auto clear time 1 4 10 sec., 2 30 sec., *3 90 sec., 5 120 sec., 6 60 sec., OFF 2 Preheat mode *14 7 30 sec., 2 60 sec., 3 30 min., 5 60 min., 6 240 min. 5 min., 120 min., 3 Auto power shut- off mode *1 ON, 2 OFF 4 Auto power shut- off timer *14 5 min., 2 30min., 3 120 min., 5 240 min. 60 min., Program No. Mode Parameters 6 SPF automatic original discharge time 13 5 5 min., ...
Questo manuale è adatto anche per i modelli :Stampanti - AL-2030 (4.05 mb)