valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
This also applies to other types of print media. Media and tray 2. Menu Overview and Basic Setup 34 • Always load the specified print media only to avoid paper jams and print quality problems (see "Print media specifications" on page 104). • Flatten any curl on postcards, envelopes, and labels before loading them into the multi-purpose (or manual feeder) tray. 1 Pull out the paper tray for manual feeding. OR Press the push-release of multi-purpose tray and it down to open. 2 Load the paper. 3 Squeeze the multi-purpose (or manual feeder) tray paper width guides and adjust them to the width of the paper. Do not force them too much, or the paper will bent resulting in a paper jam or skew. CLP-41xN Series/CLP-41xNW Series CLP-68xND Series/ CLP-68xDW Series CLP-41xN Series/CLP-41xNW Series CLP-68xND Series/ CLP-68xDW Series CLP-41xN Series/CLP-41xNW Series CLP-68xND Series/ CLP-68xDW Series 2 1 Media and tray • When printing the special media, you must follow the loading guideline Media and tray • When printing the special media, you must follow the loading guideline (See "Printing on special media" on page 35). Printing on special media • When papers overlap when printing using multi-purpose tray, open tray 1 and remove overlapping papers then try printing again. When you print a document, set the paper type and size for the multipurpose (or manual feeder) tray (see "Setting the paper size and type" on page 40). The settings made from the machine driver override the settings on the control panel. a To print in application, open an application and start the print menu. b Open Printing Preferences (See "Opening printing preferences" on page 43). c Press the Paper tab in Printing Preferences, and select an appropriate paper type. For example, if you want to use a label, set the paper type to Label. d Select Manual Feeder (or MP Tray) in paper source, then press OK. e Start printing in application. If your machine has multi-purpose tray, press OK on the control panel each time you load a sheet of paper. The table below shows the special media usable in tray. The media is also shown in the Printing Preferences. To get the highest printing quality, select the proper media type from the Printing preferences window > Paper tab > Paper Type (see "Opening printing preferences" on page 43). For example, if you want to print on labels, select Labels for Paper Type. • When using special media, we recommend you feed one sheet at a time (see "Print media specifications" on page 104). • Illustrations on this user’s guide may differ from your machine depending on its options or models. Check your machine type (see "Front view" on page 17). To see for paper weights for each sheet, refer to "Print media specifications" on page 104. Types Tray 1 Optional traya Manual feeder/ Multipurpose tray Plain . . . Thick . . . Thicker . . 2. Menu Overview and Basic Setup 35 Media and tray 2. Menu Overview and Basic Setup 36 (.: Supported, Blank: Not supported) Envelope Printing successfully on envelopes depends upon the quality of the envelopes. To print an envelope, place it as shown in the following figure. • When selecting envelopes, consider the following factors: - Weight: should not exceed 90 g/m2 otherwise; jams may occur. - Construction: should lie flat with less than 6 mm curl and should not contain air. - Condition: should not be wrinkled, nicked, nor damaged. - Temperature: should resist the heat and pressure of the machine during operation. • Use only well-constructed envelopes with sharp and well-creased folds. • Do not use stamped envelopes. Thin . . . Cotton . . Color . . Preprinted . . Recycled . . . Envelope . . Transparency . . Labels . . CardStock . . . Bond . . . Archive . . . Letterhead . . . Punched . . . Glossy Photo . . . a. CLP-68xND Series/CLP-68xDW Series only. Types Tray 1 Optional traya Manual feeder/ Multipurpose tray CLP-41xN Series/CLP-41xNW Series CLP-68xND Series/ CLP-68xDW Series Media and tray 2. Menu Overview and Basic Setup 37 • Do not use envelopes with clasps, snaps, windows, coated lining, selfadhesive seals, or other synthetic materials. • Do not use damaged or poorly made envelopes. • Be sure the seam at both ends of the envelope extends all the way to the corner of the envelope. 1 Acceptable 2 Unacceptable • Envelopes with a peel-off adhesive strip or with more than one flap that folds over to seal must use adhesives compatible with the machine’s fusing temperature for 0.1 second about 170°C (338 °F). The extra flaps and strips might cause wrinkling, creasing, or jams, and may even damage the fuser. • For the best print quality, position margins no closer than 15 mm from the edges of the envelope. • Avoid printing over the area where the envelope’s seams meet. Transparency In case of color printing using transparencies, the picture quality would be lower than mono printing when the printouts are used on the overhead projector. To avoid damaging the machine, use only transparencies designed for use ...
Questo manuale è adatto anche per i modelli :Stampanti - CLP-415N (27.08 mb)
Stampanti - CLP-680DW (27.08 mb)
Stampanti - CLP-680ND (27.08 mb)
Stampanti - Wireless Color Laser Printer CLP-415 (27.08 mb)