valutazioni - 3, GPA: 3.3
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
1 Load a sheet of print material with the print side down and against the right edge of the Multi-purpose Tray. 2 Pinch the paper width guide and slide it to the right to touch lightly against the edge of the paper without bending it. 3.12 USING PRINT MATERIALS 3 When you print a document, you must select Manual for Source in the software application, and then select the correct paper size and type. For details, see page 4.7. 3 4 Print the document. The display shows a message prompting you to load paper. 5 Press the On Line/Continue button ( ). The printer picks up the print material and prints. After one page is printed, the message appears again. 6 Insert the next sheet into the Multi-purpose Tray and press the On Line/Continue button ( ). Repeat this step for every page to be printed. USING PRINT MATERIALS 3.13 Printing on Special Print Materials Printing on Envelopes • Load envelopes into the Multi-purpose Tray only. • Only use envelopes recommended for laser printers. Before loading envelopes in the Multi-purpose Tray, make sure that they are undamaged and are not stuck together. • Do not feed stamped envelopes. • Never use envelopes with clasps, snaps, windows, coated linings, or self-stick adhesives. To print on envelopes: 1 Open the Multi-purpose Tray and unfold the paper support. 2 Flex or fan the edge of the envelope stack to separate them before loading. 3 Load the envelopes into the Multi-purpose Tray with the flap side up. The end of the envelope with the stamp area enters the printer first. 3.14 USING PRINT MATERIALS 4 Pinch the paper width guide and slide it to the right to touch 3 lightly against the edge of the stack without bending it. 5 When you print, configure the paper source to MP Tray, the paper type to Envelope and the paper size in the software application. For details, see page 4.7. USING PRINT MATERIALS 3.15 Printing on Labels • Only use labels recommended for laser printers. • Verify that the labels’ adhesive material can tolerate a fusing temperature of 180°C (356°F) for 0.1 seconds. • Make sure that there is no exposed adhesive material between the labels. Exposed areas can cause labels to peel off during printing, which can cause paper jams. Exposed adhesive can also cause damage to the printer components. • Never print on the same sheet of labels more than once or print on a partial sheet of labels. • Do not use labels that are separating from the backing sheet or are wrinkled or damaged in any way. • To prevent labels from sticking together, do not let the printed label sheets stack up as they are printed out. To print on labels: 1 Open the Multi-purpose Tray and unfold the paper support. 2 Load labels only in the Multi-purpose Tray with the print side down and the top, short edge in first. Adjust the guide to fit the width of the labels. 3.16 USING PRINT MATERIALS 3 When you print, configure the paper source to MP Tray, the paper type to Labels and the size in the software application. For details, see page 4.7. 3 Printing on Transparencies • When you print a color document do not use transparencies with an attached backing sheet. This may cause print quality problems. • Only use transparencies recommended for use in laser printers. • Ensure that transparencies do not have torn edges and are not wrinkled or curled. • Hold the transparencies by the edges and avoid touching the print side. Oils from your fingers can cause print quality problems. • Be careful not to leave fingerprints on or scratch the print side. • You should use the following paper type: A4: 003R96002, Letter: 3R3108 NOTE: Before printing on transparencies, make sure that the output support is laid down. USING PRINT MATERIALS 3.17 To print on transparencies: 1 Open Multi-purpose Tray and unfold the paper support. 2 Only load transparencies into the Multi-purpose Tray. They must be loaded with the print side downwards and the top with the white leading edge entering the printer first. Adjust the guide to fit the width of the transparencies. 3.18 USING PRINT MATERIALS 3 When you print, configure the paper source to MP Tray, the paper type to Transparency, and the paper size in the software application. For details, see page 4.7. 3 NOTES: • To prevent transparencies from sticking together, do not let the printed sheets stack up as they are printed out. • Place transparencies on a flat surface after removing them from the printer. • Prints made on transparency film with this printer are not compatible with overhead projectors and may appear as a black and white image if projected. USING PRINT MATERIALS 3.19 Printing on Preprinted Paper • Preprinted paper is paper that has some type of printing placed on it before it is sent through the printer (paper that has a preprinted logo at the top of the page, for example). • Letterhead must be printed with heat-resistant ink that will not melt, vaporize, or release hazardous emissions when subjected to the printer’s fusing temperature of 180°C (356°F) for 0.1 seconds. ...
Questo manuale è adatto anche per i modelli :Stampanti - CLP-500 (9.71 mb)
Stampanti - CLP-500A (9.71 mb)
Stampanti - CLP-500N (9.71 mb)
Stampanti - CLP-500NA (9.71 mb)