valutazioni - 3, GPA: 3
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
Adjust the guide to fit the width of the labels. 2 Push the output lever down. 3 When you print on heavy paper, select Bond in the Paper Type section, and then configure the paper source, and size in the software application. For details, see page 5.3. PRINT MEDIA 4.9 Printing on Labels Guidelines • Only use labels recommended for laser printers. • Verify that the labels’ adhesive material can tolerate a fusing temperature of 200°C (392°F) for 0.1 second. • Make sure that there is no exposed adhesive material between the labels. Exposed areas can cause labels to peel off during printing, cause paper jams. Exposed adhesive can also cause damage to printer components. • Do not feed a sheet of labels through the printer more than once. The adhesive backing is designed for one pass through the printer. • Do not use labels that are separating from the backing sheet or are wrinkled, bubbled, or otherwise damaged. 2 Push the output lever down. 1 Load labels in the input tray with print side up. Adjust the guide to fit the width of the labels. 3 To print on labels, configure the paper source, type and size in the software application. For details, see page 5.3. Note: To prevent labels from sticking, do not let the printed label sheets stack up as they are printed out. 4.10 PRINT MEDIA Printing on Transparencies Guidelines • Only use transparencies recommended for use in laser printers. • Insure transparencies are not wrinkled, curled, or have any torn edges. • Hold the transparencies by the edges and avoid touching the print side. Oils deposited on the transparency can cause print quality problems. • Be careful not to scratch or leave fingerprints on the print side. 1 Load transparencies in the input tray with print side up, and the top with the adhesive strip going first. Adjust the guide to fit the width of the transparencies. 2 Push the output lever down. 3 To print on transparencies, configure the paper source, type and size in the software application. For details, see page 5.3. Notes: • To prevent transparencies from sticking, do not let the printed sheets stack up as they are printed out. • Place transparencies on a flat surface after removing them from the printer. PRINT MEDIA 4.11 Printing on Preprinted Paper Guidelines • Letterhead must be printed with heat-resistant ink that will not melt, vaporize, or release hazardous emissions when subjected to the printer’s fusing temperature of 400°F (205°C) for 0.1 second. • Ink on letterhead must be non-flammable and should not adversely affect any printer rollers. • Forms and letterhead should be sealed in moisture-proof wrapping to prevent changes during storage. • Before loading preprinted paper as forms and letterhead, verify that the ink on the paper is dry. During the fusing process, wet ink can come off preprinted paper. 1 Load letterhead into the input tray with the design face up, bottom edge toward the printer. Adjust the guide to fit the width of the paper stack. 2 To print on preprinted paper, configure the paper source, type and size in the software application. For details, see page 5.3. 4.12 PRINT MEDIA Printing on Card Stocks Postcards, 3” X 5” index cards can be printed with the Samsung ML-1200 Series printer. Guidelines • Insert the short-edge first into the input tray. To print in landscape mode, make this selection through the software. Inserting paper long-edge first may cause a paper jam. • Do not print on card stock that is too small or too large. The minimum size is 76 X 127 mm (3” X 5”) for the manual input tray and 95 X 127 mm (3.8” X 5”) for the automatic input tray, and the maximum size is 216 X 356 mm (8.5” X 14”). • Set margins at least 6.4 mm (0.25 in.) away from the edges of the media in the software application. 2 Push the output lever down. 1 Load print media in the input tray with print side up, short edge first . Adjust the guide to fit the width of the media. 3 Configure the paper source, type in the printer driver’s properties (see page 5.3) and print. PRINT MEDIA 4.13 chapter This chapter explains the printing options and common printing tasks. Topics included in this chapter are: This chapter explains the printing options and common printing tasks. Topics included in this chapter are: Printing a Document Using Toner Save Mode Printing Multiple Pages on One Sheet of Paper (N-Up Printing) Fitting a Document to a Selected Paper Size Printing Posters Setting Graphic Properties Printing Watermarks Using Page Overlay Reprinting the Last Page Printing in a Network Environment 55 Printing a Document This procedure describes the steps required for printing from various Windows applications. The exact steps for printing a document may vary depending upon the application program. Refer to your software application’s documentation for the exact printing procedure. 1 Open the document to print. 2 Select Print from the File menu. The Print dialog box is displayed (the Print dialog box for your application may look slightly diffe...
Questo manuale è adatto anche per i modelli :Stampanti - ML-1010 (3.89 mb)
Stampanti - ML-1010H (3.89 mb)
Stampanti - ML-1210H (3.89 mb)
Stampanti - ML-1210SF (3.89 mb)