valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
113 Combination Chart................................................................................ 114 7. SPECIFICATION Main Frame............................................................................................. 115 30 Originals Document Feeder............................................................. 118 Consumables......................................................................................... 119 INDEX...................................................................................................... 120 1. OPERATION Printing Paper The following types of print paper are not recommended for this machine. • Paper smaller than 90 mm x 148 mm, 3.6" x 5.9" • Paper larger than 268 mm x 388 mm, 10.5" xl5.2" • Paper heavier than 157.0 g/m2,41.7 lb • Paper lighter than 47.1 g/m2,12.5 lb • Roughly-cut paper • Paper of different thickness in the same stack • Buckled or curled paper • Low stiffness paper Correct curls in the paper before setting it in the machine. When you cannot correct the paper curl, stack the paper with the curl face down. Otherwise the paper might wrap around the drum or stains might appear. Store paper where it will not curl or absorb moisture. Use paper soon after it is unpacked. Only use paper where the leading edge has two right angle corners, as shown below. OPERATION Originals & Note □ Originals that can be set on the exposure glass are as follows: • Maximum size: 257 x 364 mm, 10.2" x 14.4" • Maximum total thickness: 30 mm, 1.1" • Maximum total weight: 5 kg, 11.0 lb □ If you use paste-up originals, make sure the pasted parts hold firmly to the base sheet and press the [Paste Shadow Erase] key. If the thickness of the pasteup original is more than 0.1 mm and the space between the pasted parts is less than 2 mm, 0.08", a shadow might appear on the prints. □ If you use originals that have bold letters or solid images at the leading edges, you might get prints with dirty edges. In this case, insert the widest margin first, or raise the printing speed. □ The first 5 mm, 0.2" of the leading edge cannot be printed. Make sure the leading edge margin is at least 5 mm, 0.2". Original Print □ a: 5 mm, 0.2" Preparation For Printing Preparation For Printing Loading Paper D Carefully open the paper feed table. Q Put the paper feed side plates lock lever. Adjust the side plates to match the paper size. Q Place the paper on the paper feed table. ur Note □ Correct the paper curl before setting the paper. If you cannot do so, stack the paper with the curl face down as shown. ver OPERATION J Make sure that the paper feed side plates touch the paper lightly. Put back the lock lever. Setting Up The Paper Delivery Table □ Open the paper delivery table. P Reference When the prints are not delivered in a neat stack, see => P.99 "When The Prints Are Thrown Over The Paper Delivery Table''. Lift the paper delivery end plate and move it to match the print paper size. Lift the paper delivery side plates and adjust them to the paper size. J Turn on the main switch. Standard Printing Standard Printing ® ^ ^ *s & & 0 # % ® ® <&• -s V: Printing In this manual, the word, "Printing" is used as opposed to "Copying" in order to distinguish between the process that your machine uses to make prints, and the process used by a standard copier machine. A standard copier scans in the original for each copy set made. This machine, however, scans in your original once and makes multiple prints from this master. This chapter describes the basic printing operations that your machine is capable of. Set the original face down on the exposure glass. The original should be centered according to the size marks on the right scale. Lower the platen cover. J Enter the number of prints required with the [Number] keys. TSLS011E $ Note □ Up to 9999 prints can be entered at one time. □ To change the number entered, press the [Clear/Stop] key and enter the new number. OPERATION Q Press the [Start] key. o©@ ©©© O' ©®© ©©• A trial print is delivered to the paper delivery table. Q Press the [Proof] key and check the image density and the image position of the proof print. ! ©©© „ ©©© o : ©®© - sQ i Q Press the [Print] key. or Note □ After printing is completed, the same number of prints is automatically set for the next job. □ To stop the machine during the multi-print run, press the [Clear/ Stop] key. □ To return the machine to the initial condition after printing, press the [Clear Modes] key. & Note □ If the image position is not correct, adjust it using the [Image Position] keys or the fine adjustment dial. See => P.8 "Adjusting The Print Image Position". □ If the image density is slightly dark or light, adjust the image density using the [ •*] or [►] key. See => P.10 "Adjusting The Print Image Density". Restoring Paper Feed And Paper Delivery Tables Restoring Paper Feed And Paper Delivery Tables D Remove the paper from th...