270 sec.) CT-S801 - High performance • Print speed: 300mm/sec (11.8 IPS) • fastest in its class • newly developed gate array • 32 bit RISC CPU a • 8MB SDRAM t • Resolution: 203 DPI (8 dots/mm) ' • high quality printing • smooth graphics • more characters/line CT-S801 - More features • Head Pressure Adjustment Lever Paper thickness from 65 - 150 pm • Integrated Buzzer • Standard & 2D Barcodes • Paper “near-end” detection • Updated mechanical sensor • Improved accuracy • Reduces

270mm (63.82 Lines/sec, 1/6inch feed) • 2color Max. 130mm (30.73 Lines/sec, 1/6inch feed) • Ladder Barcode: Mono 270mm/sec, 2Color 130mm/sec Paper feeding Speed • Approx. 270mm/sec Table 3-2 Thermal Printer Specification 2) 203 dpi Item Description Remark Model • SRP-F312 (TPH: KRC-80-8TA02-BIX2,KYOCERA CORPORATION) Print Method • Thermal Line Printing Dot Density • 0.125mm(8 Dots/mm) Printing Direction • Uni-direction with friction feed Printing Width •80.0mm, 640 dot Position Character / Line

1.00 - 9 - SRP-350II 1-2-3 USB Interface USB IFG-U TYPE Drawer kick-out connector Power supply connector USB connector Pin No. Signal Name Assignment (Color) Function Shell Shield Drain Wire Frame Ground 1 VBUS Red Host Power : DC5[V] / 500[mA] 2 D-White Differential Data Line 3 D+ Green Differential Data Line 4 GND Black Signal Ground 1-3 Connecting the Drawer . WARNING Use a drawer that matches the printer specification. Using an improper drawer may damage the drawer as well as the printer. .

¦ In case of trouble do not attempt to repair the printer. Ask Citizen Systems service for repair. ¦ Be careful that the printer cover does not entrap your hands or fingers. ¦ Be careful with sharp edges on the printer. Do not allow them to injure you or damage property. •May result in electric shock, burn, or injury. If the printer emits smoke, an odd smell, or unusual noise while printing, immediately abort the current print session and unplug the printer from the supply outlet. DAILY MAINTENA

The changed set value is printed. (When change of set value is repeated, the original set value is recovered). When you press the FEED button long, the set value is accepted and then the printer goes to the next setting item. 5. Returning to the memory switch select mode When the setting of the desired content is completed, open the printer cover and then close the printer cover. This allows the printer to print the setting of the changed memory switch. 6. Saving the setting and exiting the memo

11 1-4-2 Parallel & USB2.0 Interface........................................................................11 1-4-3 Auto Cutter Enable / Disable selection .......................................................12 1-5 Setting the Memory Switches .................................................................................13 1-6 Installing or Replacing the Paper Roll.....................................................................16 1-7 Adjustments and Settings............................

*58 mm is only for label supporting model. 4. Change the setting of paper width by reffering to the section 5.2, "Manual Setting of Memory Switch". Partition Partition Scales 3.6 Setting DIP Switch CAUTION! When using 112 paper roll, the partition is not used. 3.5 Partition for Paper Roll At the time of shipment, this partition is not installed. 1. Confirm that the power switch is OFF. 2. Open the printer cover. 3. Insert the partition into the slot and align it with the scale inside of the prin

22 3.5 Partition for 58-mm Wide Paper Roll ......................................... 23 3.6 Long Life Print (LLP) Function Settings ..................................... 24 3.7 Loading Paper .............................................................................. 25 3.8 Attaching the Power Switch Cover ............................................ 26 3.9 Installing the Driver and Utilities................................................26 4. MAINTENANCE AND TROUBLESHOOTING..................

Otherwise, burning or injury of hand may result. — 17 — 4.2 Removing Jammed Paper 4.2 Removing Jammed Paper 1. Turn the printer power off. 2. Open the printer cover. 3. Remove the jammed paper including any paper chips remaining. (Remove the paper roll set in the holder as well.) 4. Reinstall the paper roll and close the printer cover. 5. Turn on the printer. The auto cutter mechanism is initialized and the alarm is cleared. CAUTION! ¦ If the cutter blade remains protruded with paper jammed, pre

It cannot be positioned vertically or on a wall. Horizontal position Vertical position CAUTION Do not use the printer under the following conditions. • Locations subject to vibration or instability. • Locations that are very dirty or dusty. • Locations where the printer is not level. • The printer may fall and cause an injury. • The quality of printing may deteriorate. • Oriented other than as specified. • The printer may malfunction, be damaged, or cause an electric shock. —23— 3.6 Partition fo