Log:
valutazioni - 4, GPA: 4.5 ( )

Istruzioni per l'uso KitchenAid, Modello 2313684A

Produttore : KitchenAid
File Size : 1.05 mb
File Nome : 7e0455a7-c77e-4f5f-9a79-5ab49a51909e.pdf
Lingua di insegnamento: enfr
Vai a scaricare



Facilità d'uso


Screw 8. Turn the water pan drain pump one-quarter turn and remove it. Place the pump on the bottom of the ice bin. 9. Remove the two thumb screws that hold the water pan in place. Push down with one hand on the front of the pan while pulling forward on the bottom back side. A B B C D A. Water pan B. Water pan thumb screws C. Water Pan Drain Pump D. Drain cap 10. Remove, clean and replace the ice scoop and ice scoop holder. ¦ After removing the ice scoop, remove the holder by removing the two thumb screws. ¦ Wash the ice scoop holder along with the other interior components using the following instructions. ¦ Replace the ice scoop holder by replacing the thumb screws. A B A. Thumb screw B. Ice scoop holder 11. Wash the interior components (cutter grid, exterior of hoses, and water pan) and the storage bin, door gasket, ice scoop, and ice scoop holder with mild soap or detergent and warm water. Rinse in clean water. Then clean the same parts with a solution of 1 tbs (15 mL) of household bleach in 1 gal. (3.8 L) warm water. Rinse again thoroughly in clean water. NOTE: Do not remove hoses. Do not wash plastic parts in dishwasher. They cannot withstand temperatures above 145°F (63°C). 12. Replace water pan by pushing back on the bottom with one hand while pushing up and back on the top. Secure the water pan by replacing both screws. 13. Replace the water pan drain pump by aligning the slots in the water pan to the tabs in the pump. Push the pump and the water pan together, then rotate the pump one-quarter turn. 14. Check the following: ¦ Drain cap from the water pan is securely in place. If the drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice. ¦ Hose from water pan is inserted into storage bin drain opening. ¦ Be sure that the water pan drain pump is fully inserted into the water pan. If the pump is loose, water will empty from the water pan and cause poor or no ice production. 15. Slide the cutter grid back into place and secure it by replacing the right-hand screw and plastic spacer. Then tighten the left-hand screw. Reconnect the cutter grid harness and the ice level sensor harness. 16. Replace the cutter grid cover and the two screws. 17. Plug in ice maker or reconnect power. Vacation and Moving Care WARNING Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. To shut down the ice maker: 1. Unplug ice maker or disconnect power. 2. Remove all ice from storage bin. 3. Shut off the water supply. 4. Remove the two screws in the lower access panel and the two screws from the base grille area of the front panel support. Pull forward to remove the lower access panel. 5. Disconnect the inlet and outlet lines to water valve. Allow these lines to drain and then reconnect to the valve. 6. Replace lower access panel and screws. 7. Drain water from water pan by removing the drain cap. 8. If the room temperature will drop below 32°F (0°C), remove water from the drain line. For ice makers with a drain pump installed: ¦ Plug in ice maker or reconnect power. ¦ Turn ice maker off and remove all remaining ice from ice bin. ¦ Pour 1 qt (0.95 L) of water into the ice bin near the drain and let the unit stand for approximately 5 minutes. This will allow the water in the bin to drain into the drain pump so that the pump will remove the remaining water from the ice bin and the drain pump. ¦ Unplug ice maker or disconnect power. 9. Before using again, clean the ice maker and storage bin. 10. Plug into a grounded 3 prong outlet. NOTE: All components of the ice maker are permanently lubricated at the factory. They should not require any additional oiling throughout the normal life of the machine. TROUBLESHOOTING Try the solutions suggested here first in order to avoid the cost of an unnecessary service call. Ice Maker Operation Your ice maker will not operate WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. ¦ Is the power cord plugged in? Plug into a grounded 3 prong outlet. ¦ Is the control set to ON? Be sure that the control is set to ON. ¦ Has a household fuse blown, or has a circuit breaker tripped? Replace the fuse or reset the circuit breaker. If the problem continues, call an electrician. ¦ Is the room temperature cooler than normal? Room temperature must be above 55°F (13°C). Otherwise, bin thermostat may sense cold room temperature and shut off even though the bin is not full of ice. Also, unit may not restart once it does shut off. ¦ Does the red light come on when the Clean button is pushed? The ice maker is receiving power but may need cleaning. See “Cleaning.” ¦ Does the ice maker have a drain pump? If there was a large amount of water added to the ice maker, wait a few minutes ...


Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie