valutazioni - 4, GPA: 4 ( )

Produttore : Cleveland Range File Size : 2.11 mb File Nome : Lingua di insegnamento:

The unit should not be heating or cooling at this point. 5. Push (*) button on CAL 9900 to read set point temperature. (This is the desired product temperature). 6. To change set point temperature push and hold (*) button while pushing (A ) or (V ) button. New set point is determined when (*) button is released. 7. Add product to kettle. 8. Turn ACTIVE/BYPASS switch to “ACTIVE”. If the set point temperature is higher than the BYPASS ACTIVE product temperature, the kettle will start heating. Note: For twin kettles, the CAL 9900 will control the kettle the mixer is in. The controller has been preset at the factory and should operate satisfactory. If you wish to fine tune the unit for your specific application consult the CAL 9900 Installation and Operation Manual. Following is a simplified procedure for changing parameters. 1. Mixer MAIN POWER switch in the position. ON1 2. ACTIVE/BYPASS switch in ‘BYPASS' position. 4. To change the OPERATING MODE setting push the (A) or (V) buttons. To move to the FUNCTION NUMBER (right of the decimal) push (*) button. ■ E.IB ■ i .IE 6. That number should now be flashing. To move to another FUNCTION NUMBER push the (A)or (▼) buttons. 7. Push (*) button to move tothe left of the decimal. To change the OPERATING MODE setting push the (A) or (V) buttons. 8. When your changes are complete push the button labeled (p) again to return to the Process Temperature. ■ .IE 1 CAL 9900 °C 1 / ■ /. IE ■ 5W 3. Press button labeled (p). The display should show a number with a decimal place in it. Left of the decimal weraung nwcnoN place is the OPERATING MODE setting (this number should be flashing). To the right is the FUNCTION NUMBER. Cleveland Range Factory Settings OPERATING MODE FUNCTION NUMBER 0 0 0 1 5 2 0 3 4 steam 5 electric 4 0 5 5 6 0 7 0 8 1 9 0 10 0 11 0 12 0 13 0 14 0 15 9 16 0 17 0 18 1 19 2 T.A.P 0 20 0 21 —». O 1 1 1 1 F O 22 6 23 -- -- 24 0 25 -- -- 26 MRC 7000 Controls Drawing (1 pen) OFF HEAT AUTO COOL BYPASS ACTIVE OFF ON MIXER KETTLE OPERATION USING MRC 7000 (1 PEN) Note: Temperature probe on mixer bridge must be covered with a minimum of three inches of product to function correctly. 1. Turn MAIN POWER switch to "ON". 2. Turn HEAT/COOL switch to "OFF/AUTO". 3. Turn ACTIVE/BYPASS switch to "ACTIVE". 4. Open steam valve completely 5. On controller keypad push and hold key " " or " " until desired temperature is set. 6. To start: push scroll key " Q)" until "CtrL" is displayed. 7. Push down key " ". 8. To stop: push scroll key " ^)" until "OFF" is displayed. 9. Push down key " ". NOTE: For twin kettles, the MRC 7000 will control the kettle the mixer is in. BYPASS ACTIVE If the unit is used continually it may be simpler to control the "ON/OFF" function with the following steps: 1. Keep HEAT/COOL switch at "OFF/AUTO". 2. To stop turn ACTIVE/BYPASS switch to "BYPASS". 3. To change temperature setting push and hold key " " or " " until desired temperature is set. 4. To start, turn ACTIVE/BYPASS switch to "ACTIVE". CLEANING INSTRUCTIONS A CAUTION /m SURFACES MAY BE EXTREMELY HOT! CARE AND CLEANING Cooking equipment must be cleaned regularly to maintain its fast, efficient cooking performance and to ensure its continued safe, reliable operation. The best time to clean is shortly after each use (allow unit to cool to a safe temperature). WARNINGS о Chloride Cleaners о о о High Pressure Spray Hose о Do not use detergents or cleansers that are chloride based or contain quaternary salt. Do not use a metal bristle brush or scraper. Steel wool should never be used for cleaning the stainless steel. Unit should never be cleaned with a high pressure spray hose. Do not leave water sitting In unit when not in use. Stagnant Water CLEANING INSTRUCTIONS 1. Turn unit off. 2. Remove drain screen (if applicable). Thoroughly wash and rinse the screen either in a sink or a dishwasher, 3. Prepare a warm water and mild detergent solution in the unit. 4. Remove food soil using a nylon brush, 5. Loosen food which is stuck by allowing it to soak at a low temperature setting. 6. Drain unit, 7. Rinse interior thoroughly, 8. If the unit is equipped with a Tangent Draw-Off Valve, clean as follows: a) Disassemble the draw-off valve first by turning the valve knob counter-clockwise, then turning the large hex nut counter-clockwise until the valve stem is free of the valve body, b) In a sink, wash and rinse the inside of the valve body using a nylon brush, c) Use a nylon brush to clean tangent draw-off tube, d) Rinse with fresh water, e) Reassemble the draw-off valve by reversing the procedure for disassembly. The valve's hex nut should be hand tight only. 9. If the unit is equipped with a Butterfly Valve, clean as follows: a) Place valve in open position, b) Wash using a warm water and mild detergent solution. c) Remove food deposits using a nylon brush, d) Rinse with fresh water, e)...

Scarica la tua

Per scaricare, digitare 2 cifre :