valutazioni - 4, GPA: 4.5
(
)
)
|
Facilità d'uso
C Warming Oven . The specified minimum cabinet depth and width must be 120 VacD provided. The cabinet depth and width must completely electrical enclose the recessed portion of the oven. outlets C Warming Oven . Cabinet cutout dimensions must be used as indicated. All contact surfaces between the appliance and the cabinet must be solid and level. The oven support platform must be flush Toe Kick with the bottom edge of the cabinet cutout. 5/8” Min. A (16mm) . Make certain that you have everything necessary to ensure a proper installation before proceeding. Stacked Installation with Wall Oven NOTES: 1. Minimum Cutout Depth: Model IOWO24 - 20” (508mm) All other models - 23 3/8” (594mm) 2. The IOWO24 and EWO36 models cannot be stacked. 3. The IOWO24 warming oven is not approved for installation under a wall oven. Model “A” Cutout Width “B” Min. Width to Adjacent Doors/Drawers “C” Cutout Height “D” Min. Gap Between Cutouts IOWO24 22 9/16” (573mm) N/A* 12 1/8” (308mm) N/A* IWO24 22 1/2” (572mm) 9 1/8” (232mm) EWO24 24 1/4” (616mm) 1 1/16” (27mm) EW27 25 1/2” (648mm) 27 1/4” (692mm) EWO27 IWO27 N/A* N/A* MW27 27 1/4” (692mm) 1 1/16” (27mm) MWO27 PW27 EW30 30 1/4” (768mm) EWO30 MW30 MWO30 PW30 PWO30 EWO36 34 3/8” (873mm) 36 1/4” (921mm 3” (76mm) * Depends on size of cabinet face installed. Table 1: Cutouts Dimensions InstallatIon specIfIcatIons 1 1/2" (38mm) Typical countertop 3/4" Min. (19mm) 5/8" Min. (16mm) Warming Oven Cooktop 120 Vac electrical outletA 36" Typ. (914mm) B C Single Installation to Side of Cooktop A Warming Oven Warming Oven OB Outdoor Grill EG Epicure Gas Cooktop 120 Vac electrical outlet 36" typ. (914mm) C C 3/4" Min. (19mm) D 5/8" Min. (16mm) B Stacked Installation Below Cooktop or Grill InstallatIon specIfIcatIons p WARNING oWer supply requIrements Electric shock Hazard – This appliance is equipped with a 40” (1016mm) power cord with a three prong grounded plug. Plug it only into a grounded three prong electrical outlet. • Do not remove the ground prong. • Do not use a 2-prong adapter. • Do not use an extension cord. • Do not use a power cord that is frayed or damaged. Failure to comply with the above can result in fire, electric shock, or death. The electrical outlet for this appliance must only be installed by a licensed electrician. Power cord with three-prong grounding plug Grounding type electrical outlet The correct voltage, frequency and amperage must be supplied to the electrical outlet from a grounded, single phase circuit that is protected by a properly sized circuit breaker or time-delay fuse. Circuit Requirements: . 120 Vac, 60 Hz, 15 Amp. dedicated circuit. Total Connected Load: . Model EWO36: 0.8kW (6.5 Amp.) . All other models: 0.5kW (4 Amp.) NOTES: 1. The above specifications are for reference only. Refer to the product date label for exact specifications. If the requirements above do not agree with those listed on the product data label, use the information found on the label. See inside the front cover for location. 2. If the electrical service provided does not meet the product specifications, or does not conform to the NEC or local standards, do not proceed with the installation. Call a licensed electrician to install the required electrical service before proceeding. 3. Be certain to locate the electrical outlet in an accessible location, so that the warming oven may be easily unplugged if service becomes necessary. 4. It is the owner’s responsibility to ensure that the electrical outlet for this appliance has been installed by a qualified electrician. The electrical installation must comply with the latest revision of the National Electric Code ANSI/NFPA 70 and local codes and ordinances. InstallIng the support platform In the cabInet Provide a platform (100lb. load capacity) within the cabinet upon which the warming oven will be supported. The platform must be installed level and straight. The top edge of the platform must be flush with the cutout at the front of the cabinet. There are no provisions to level the warming oven after it has been installed. 3/4” (19mm) thick plywood is recommended. NOTE: If the oven is not installed in a level fashion, the drawer may slide open on its own or may not seal tightly, allowing heat to escape and resulting in poor performance. SupportplatformChassisface InstallatIon InstructIons verIfyIng the package contents • Use and care manual • Mounting screws • Wire rack with mounting hardware (IOWO model only) removIng the DraWer WARNING 1. Verify that the electrical outlet for the warming oven meets the Power Supply Requirements on the facing page before proceeding. 2. Be certain that power plug is disconnected from the electrical outlet before installation. Remove the drawer from the appliance to allow access to the mounting holes during installation, and to reduce weight: 1. Pull the drawer out to the fully open position. 2. Push in on the locking tab on one side as you pull the drawer up. 3. When the drawer comes loose on the slide, re...
Questo manuale è adatto anche per i modelli :Altri elettrodomestici da cucina - IOWO (451.07 kb)